Inficon Easy Rate ERD E1 Series Instruction Sheet Download | Manualshive

Page: 11 / 13

background image

11 of 13

Easy Rate Sensor

PN 074-677-P1A

Tools:

Soldering iron, adjustable wrench, Teflon

™

tweezers, torque screwdriver or

wrench

1

Grasp the microdot connector by the flat sides using an adjustable wrench and
loosen it. (See

Figure 8 Microdot connector

NOTE:

If the wire inside is still intact, the connection will break as the connector
comes loose. This is normal and expected.

2

Pull the crystal holder out of the sensor body. (See

Figure 9 Remove crystal holder

«
...
9
10
11
12
13
»

Summary of Contents for Easy Rate ERD E1 Series














Reviews:

No comments

Related manuals for Easy Rate ERD E1 Series

Brand: Canon Pages: 12

Brand: Campbell Pages: 46

Brand: V-ZUG Pages: 12

Brand: Metra Electronics Pages: 14

Speedglas G5-02

Brand: 3M Pages: 17

Speedglas 9100 MP

Brand: 3M Pages: 72

Speedglas 9100-Air

Brand: 3M Pages: 63

Brand: 3M Pages: 84

Brand: Garland Pages: 36

Brand: 4MOMS Pages: 20

Brand: Lamtec Pages: 18

Brand: Ladybug Pages: 33

Oakville Series

Brand: Napoleon Pages: 72

Brand: Napoleon Pages: 4

Allure Vertical Series

Brand: Napoleon Pages: 120

Brand: Yakima Pages: 8

Brand: ZEPP Pages: 36

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands