Infinite Play TINF4.POE User Installation And Operation Manual Download

Page: 28 / 32

INFINITE PLAY

Appendix 3 Web browser access instructions

Note: Please set firewall rank for low or medium, and surf software or net assistant software, etc.

Should be blocked or unloaded, otherwise the software may not run properly.

Please guarantee to install DirectX 9.0 of Microsoft and confirm the nternet Explorer edition is 6.0 version

or above.

Note : Browsing way in WAN is as same as in LAN , only the address format is http://WAN ip:port or

htttps://WAN IP. Now let’s take LAN for example .

【

Step1

】

Check “ping” to link the NVR successfully.

【

Step2

】

Type the IP address of the device in IE browser and confirm to connect. The IP format should

be : https://IP or http://IP:port, after connecting successfully, login with right username and password. If

【

Step3

】

Specific operation as you can see“User Manual”.

Web browser in WAN user guide

If there is a fixed WAN IP address can be assigned to NVR, NVR can be directly access WAN ,set

IP/Subnet mask/Gateway, then link it.The Step of NVR Setting as below: Click “Menu” after logging in to

enter “networking setting”, then enter the interface “dial setting” and write down User name /Password to

make NVR to link successfully .As you can see information when NVR would be linked successfully.

Write down the IP address at IE Port to link WAN visiting.If you want to link more than one NVR as one

broad band into WAN, Please set as reference below.

First, set “IP” “Subnet mask” and “Gateway” at the Menu of Embedded NVR.

Warming:Gateway must be set by the gateway of current mapping server. Then link local area

networking and set net mapping server at dial-up Router. (Notice: the instructions of mapping server for

TCP protocol.)

2. Mapping port by router

Host network setting interface as Picture below.

Note:The command port and http port in Picture 1 default are 8101, 81. User can set these ports by

user-defined and save them.Take the TL-480T of TP-LINK for example:

【

】

Choose “Running Status” at the left Menu as showed Picture2 when you link successfully. Check

the router in the network IP address as you can see the picture below, IP Address:192.168.2.250, WAN

Summary of Contents for TINF4.POE

































Search results

Summary of Contents for TINF4.POE

Reviews:

Related manuals for TINF4.POE

Brands by name

Popular brands

Infinite Play TINF4.POE, User Installation And Operation Manual

Search results

Summary of Contents for TINF4.POE

Reviews:

Related manuals for TINF4.POE

Brands by name

Popular brands