3
The coolant fluid needs time to settle. If the appliance is switched off at any time, wait 30 minutes before switching back on
to allow the coolant fluid to settle.
Before filling your Refrigerator
Before storing foods in your Refrigerator, turn the Refrigerator on and wait for 24 hours, to make sure it is working properly
and to allow the Refrigerator drops to the correct temperature.
Electrical Connection
WARNING
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it
replaced by an authorized service center.
This refrigerator should be properly grounded for your safety. The power cord of this refrigerator is equipped with a
three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock.
Do not, under any circumstances, cut or remove the third ground prong from the power cord supplied.
This refrigerator requires a standard
230( or 220~240)V A.C. ~/50Hz
Hz electrical outlet with three-prong ground.
This refrigerator is not designed to be used with an inverter.
The cord should be secured behind the refrigerator and not left exposed or dangling to prevent accidental injury.
Never unplug the refrigerator by pulling the power cord. Always grip the plug firmly and pull straight out from the
receptacle.
Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service
technician install an outlet near the appliance. Use of an extension cord can negatively affect the performance of the unit.
START
1.
Keys
1.1 Display panel
1.2 Single key operation
1.2.1
‘Temp. Zone’ key
1
）
This key is to select the temperature zone, and the
temperature zone changes each time the key is
pressed, with the temperature of the selected zone
displayed by digits.
2
）
The temperature zone selection changes through the
following cycle:
Fridge → Freezer →Fridge ;
3
）
Every time when settings are finished (with no flickering
any more), if the ‘Temp. Zone’ key is pressed again,
‘Fridge’ starts flickering first.
1.2.2
‘Temp.’ key
1
）
Under the temperature setting state, if the temperature
zone is selected to be Fridge (with patterns of both the
left and the right fridge doors flickering at the same
time), press the ‘Temp.’key, then the two digits starts flickering, which takes effect when the ‘OK’ key is
pressed; and if the temperature zone is selected to be Freezer (with patterns of both the left and the right freezer
doors flickering at the same time and the ‘-’sign illuminated), set the freezer temperature by reference to the
fridge temperature setting.
The temperature will rise by 1
℃
with each key response, which can be set in a cyclic manner.
2
）
Adjustable temperature range for each compartment
：
Fridge compartment: 08
～
02;
Freezer compartment: -16
～
-24;
The default value for each compartment when the refrigerator is energized for the first time:
Fridge compartment temperature is 05, and freezer compartment temperature -18.
3) Fridge OFF: When the fridge temperature is set, the temperature setting progresses through the following
cycle.
2
℃
→3
℃
→4
℃
→5
℃
→6
℃
→7
℃
→8
℃
→OF→2
℃
(‘OF’ represents the OFF state, and when the OF setting takes effect, the fridge will be shut off, with no
refrigeration request.)
1.2.3
‘Function’ key
1)
The selected functionchanges with each key response.
2)
Function selection changes through the following cycle:
LECO→ Quick Freezer→ Holiday→Smart→LECO;
3)
Every time when the function setting is finished, if the ‘Function’ key is pressed again, ‘LECO’ starts flickering
first.
4)
When a function has not been set, press this key to select the function, and then press the ‘Ok’ key, the
selected function is enabled.
5)
When a function has been enabled, press this key to select the function, and then press the OK key, the
enabled function gets exited.
1.2.4
‘OK’ key
1)
Under the state of function selection or temperature setting, the selected function or the set temperature value
comes into force when this key is pressed, with the corresponding flickering stopped immediately.
2)
Under the function selection or the temperature setting state, if this key is not pressed within 5 seconds,
flickering gets stopped, with the selected function or the set temperature value invalid.
