background image

For the Infoblox-2000-A Appliance 

3

Introduction

This guide provides an overview of the Infoblox-2000-A network services appliance running Infoblox NIOS version 
5.1r1-4 and later, and explains how to install and configure it. 

Figure 1  

Tasks in This Guide

Product Overview

The Infoblox-2000-A network services appliance provides reliable, scalable, and secure core network services 
including DNS (Domain Name System), DHCP (Dynamic Host Configuration Protocol), IPAM (IP Address 
Management), IF-MAP, and more. The integrated Infoblox approach combines the simplicity of appliances with the 
power of advanced distributed database technology to control and automate services while achieving availability, 
manageability, visibility, and control unparalleled by conventional solutions based on legacy technologies. You can 
configure and manage the Infoblox-2000-A through an easy-to-use Infoblox GUI that works seamlessly in Windows, 
Linux, and Mac environments using standard web browsers.

The Infoblox-2000-A is a full-featured appliance with hot-swappable power supplies, fan modules, and hard disk 
drives. The Infoblox-2000-A is a Class A digital appliance per FCC regulations, and it is RoHS and WEEE compliant. 
The Infoblox-2000-A belongs to the modular Infoblox product line that includes the Infoblox-250-A, -550-A, 
-1050-A, -1550-A, -1552-A, and -1852-A. For information about the Infoblox platforms, visit the Infoblox web site 
at 

www.infoblox.com

.

1

2

3

Learn about the Infoblox appliances.

"Introduction" on page 3

Install appliances.

"Installing an Appliance" on page 11

Equipment 
Rack

Power 
Source

Management 
System

To 
Network

Access appliances.

"Accessing the 
Appliance" on page 21

Summary of Contents for Infoblox-1050-A





























Reviews: