background image

Page 34

enable you to ship the product to an InFocus repair service location, or (iii) by sending you customer-installable new or 
refurbished replacement parts to enable you to conduct Customer Self Repair, or (iv) by exchanging the product for a 
new or refurbished replacement.

Customer Self Repair

  

InFocus products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater 
flexibility in performing defective parts replacement. If during the diagnosis period, InFocus identifies that the repair can 
be accomplished by the use of a CSR part, InFocus will ship that part directly to you for replacement. There are two 
categories of CSR parts: 

• 

Parts for which customer self repair is mandatory.  If you request InFocus to replace these parts, you will be charged 
for the travel and labor costs of this service. 

• 

Parts for which customer self repair is optional.  These parts are also designed for customer self repair.  If, however, 
you require that InFocus replace them for you, this may be done at no additional charge under the type of warranty 
service designated for your product.  

Based on availability and where geography permits, InFocus will attempt to ship CSR parts out the next business 
day.  Customer receipt will vary based upon the actual part, customer location and shipping method. Next Day service 
may be offered at an additional charge where geography permits. If assistance is required, you can call the InFocus 
Technical Support Center and a technician will help you over the phone. InFocus specifies in the materials shipped with 
a replacement CSR part whether a defective part must be returned to InFocus.  In cases where it is required to return 
the defective part to InFocus, you must ship the defective part back to InFocus within a defined period of time, normally 
five (5) business days, and clearly display the Return Material Authorization (RMA#) on the outside of the shipping carton 
or a similar package affording an equal degree of protection. The defective part must be returned with the associated 
documentation in the provided shipping material. Failure to return the defective part may result in InFocus charging you 
for the replacement. With a Customer Self Repair, InFocus will pay all shipping and part return costs and determine the 
courier/carrier to be used.

Upon receipt of the replacement product or part, the original product or part becomes the property of InFocus and you 
agree to follow instructions, including arranging the return of original product or part to InFocus in a timely manner. 
When providing a product exchange or Customer Self Repair (CSR) part requiring the return of the original product or 
part, InFocus may require a credit card authorization as security for the retail price of the replacement product or part 
and applicable shipping costs. When returning product to InFocus, a Return Material Authorization Number (RMA #) is 
required and must be clearly displayed on the outside of the shipping carton or a similar package affording an equal 
degree of protection. Service options, parts availability and response times may vary according to the country in which 
service is requested. Service options are subject to change at any time. You may be responsible for shipping and 
handling charges if the product cannot be serviced in the country in which service is requested. If you seek service in 
a country that is not the country of original purchase, you will comply with all applicable import and export laws and 
regulations and be responsible for all custom duties, V.A.T. and other associated taxes and charges. Where international 
service is available, InFocus may repair or exchange defective products and parts with comparable products and parts 
that comply with local standards. In accordance with applicable law, InFocus may require that you furnish proof of 
purchase details and/or comply with registration requirements before receiving warranty service. Resources with more 
details on this and other matters on obtaining warranty service are described below. 

PRIVACY.

 InFocus will maintain and use customer information in accordance with the InFocus Privacy Policy available 

at www.Infocus.com/privacy and InFocus’s applicable legal obligations. 

BACKUP.

 If your product is capable of storing software programs, data and other information, you should protect 

its contents against possible operational failures. Before you deliver your product for warranty service it is your 
responsibility to keep a separate backup copy of the contents, remove all personal information and data that you want 
to protect and disable any security passwords. THE CONTENTS OF YOUR PRODUCT WILL BE DELETED AND THE 
STORAGE MEDIA REFORMATTED IN THE COURSE OF WARRANTY SERVICE. Your product or a replacement product 

Summary of Contents for MONDOPAD INF5720






































Reviews: