background image

Page 5

INF7023 Series Hardware Guide

• 

Do not use any components of the display, including the speakers, near water. Warning: To reduce the risk of fire or electric shock, do not expose this equipment or 
any component of this equipment to rain or moisture.

• 

Do not drop the display.

• 

Do not spill liquid on the display. Spilled liquid may damage the display.

• 

WARNING: This display must be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury or death.

• 

The power outlet used to power this display should be readliy accessible for fast disconnection in case  
of emergency.

• 

No naked flame source, such as lighted candles, should be placed on the display.

• 

Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal. A surge-protected power strip is 
recommended. Do not overload wall outlets.

• 

It is recommended that the Class 1 display be grounded.

• 

Do not install the display in places subject to mechanical vibration.

• 

Do not place the display on an unstable surface, which could result in serious personal injuries and display damage. When mounting the display to a stand, be sure 
to following the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

• 

When disconnecting the power cord, hold the plug, not the cord.

• 

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the display.

• 

Unplug the display if you are not going to use it for an extensive period of time.

• 

Unplug the display if you need to clean it with the included microfiber cleaning cloth. The screen may be wiped with the cleaning cloth when the power is off. Never 
use alcohol, solvents or ammonia-based liquids on this display.

• 

Wash hands after handling the cables supplied with this display.

• 

The display remote control, mouse and keyboard use batteries. Make sure the batteries’ polarity (+/-) is aligned correctly. Dispose of used batteries in accordance 
with local disposal laws.

• 

Only use properly rated wall and stand mounting hardware that meet this product’s specifications and follow the manufacturer installation instructions. The 
warranty does not cover any damage caused by use of improperly rated mounting hardware or from improper installation.

• 

Refer all service to qualified service personnel. Do not remove the cover or back. Servicing your own display can be dangerous to you and will void the warranty.

• 

Only use replacement parts specified by InFocus. Unauthorized substitutions may result in fire, electrical shock or injury and may void the warranty.

• 

When mounting the display to a wall, metric 8 (12mm) screws must be used. In addition, the mounting interface should comply with the UL1678 standard in North 
America. The mounting means should be strong enough to bear the weight of the display.

• 

Follow these instructions to help ensure image quality over the life of the display. Failure to follow these instructions may affect the warranty. 

• 

Lithium Battery (in PC Box) Caution: There is a risk of explosion if the battery is replaced by an incorrect type.  The battery should only be replaced with an identical 
or equivalent type of battery as recommended by the manufacturer.  Dispose of used batteries in accordance with local disposal laws.

安全資訊

在將本產品連接到電源前,請仔細閱讀並遵守以下列出以及產品上的所有安全指示。未遵守安全指示可能會導致火災、電擊或人身傷害,並可 能破壞或損
壞設備所提供的保護。請保存所有安全指示。

•  此顯示器非常重,至少需要兩個人移動並完成安裝。請勿自己嘗試移動或安裝顯示器,否則會造成傷害和/或損壞。
•  移動顯示器時,請務必使用手柄和側外框或底部外框牢牢托住顯示器。請勿抓握頂部外框。
•  移動顯示器包裝箱時,請勿傾斜或倒置包裝箱。始終保持直立。
•  移動顯示器前,請斷開所有配件和線纜。
•  如果將顯示器裝在牆上,請在顯示器和牆壁之間保留最少 1.98 英寸(5 釐米)的距離,以保持足夠通風。
•  有關正確開機和關機流程,請參閱本指南。
•  請遵循本手冊中以及顯示器上的所有警告和注意事項。
•  顯示器的擺放位置應與加熱和冷卻通風孔保留至少 4 英尺(1.2 米)的距離。
•  請勿堵塞通風口。將顯示器置於通風良好的區域,且進氣口或排氣口無阻塞。
•  請勿在散熱器、電熱器、火爐或其他產生熱量的設備(包括放大器)等熱源附近安裝或使用顯示器或條形音箱。
•  請勿將顯示器放在陽光直射、潮濕、油膩或積塵,或顯示幕可能接觸到雨水、煙霧或蒸汽的區域。
•  請勿在電源線靠近浴缸、洗臉盆、廚房水槽、游泳池附近等有水的區域使用顯示器。
•  請勿在靠近水的區域使用顯示器的任何元件,包括條形音箱。警告:要降低火災或電擊風險,請勿使本設備或其元件淋雨或受潮。
•  請勿拋擲顯示器。
•  請勿將液體濺灑在顯示器上。濺落的液體可能會損壞顯示器。
•  警告:必須按照安裝指示將本顯示器牢固地固定在地板/牆面上。傾斜、搖晃或搖動機器可能會造成人身傷害或致死。
•  用於為此顯示器提供電力的電源插座應置於便於觸及的地方,以便在出現緊急情況時快速斷開連接。
•  請勿將點燃的蠟燭等明火火源放在顯示器上。
•  請使用附帶的電源線。將電源線連接到附帶防護安全(接地)接地端子的插座。建議使用具有電湧保護功能的電源板。請勿超負荷使用壁式插座。
•  建議將 1 類顯示器接地。
•  請勿將顯示器安裝到易受機械振動影響的地方。

Summary of Contents for Mondopad INF7023









































Reviews: