The Ingersoll Rand Blower Purge Desiccant Dryers are designed to
adsorb moisture from compressed air. The dryers are constructed with
two towers, each containing desiccant beads, that alternate between on-
line (drying) and offline (regenerating) modes, yielding a continuous
stream of dry air at the dryer's outlet.
During normal operation, wet air passes through the on-line tower and
water vapor from the air is adsorbed (collected) on the desiccant beads.
While air is being adsorbed in the on-line tower, the moisture on the
desiccant in the offline tower is removed by a process called desorption
(regeneration). In standard blower purge operation, after an initial rapid
depressurization, air from a blower on the dryer skid passes through a
2
HB Series Desiccant Dryer Models 150-8000
ingersollrandproducts.com
heater and over the desiccant bed and carries the moisture off the bed
and out the dryer's exhaust. With the dryer's Bi-Mode feature, the
dryers may also be operated in a Heatless mode, which uses dry
compressed air as the purge air source but does not require use of the
heater or blower.
The continuous, alternating process of adsorption and desorption is
controlled using a customized Programmable Logic Controller that
switches the towers in a specific timed sequence. Very dry compressed
air dew points are achieved through the continuous switching and
operation of this dryer.
The Company warrants that the equipment manufactured by it and
delivered hereunder will be free of defects in material and workmanship
for a period of twelve months from the date of placing the Equipment in
operation or eighteen months from the date of shipment from the factory,
whichever shall first occur. The Purchaser shall be obligated to promptly
report any failure to conform to this warranty, in writing to the Company
in said period, whereupon the Company shall, at its option, correct such
nonconformity, by suitable repair to such equipment or, furnish a
replacement part F.O.B. point of shipment, provided the Purchaser has
stored, installed, maintained and operated such Equipment in
accordance with good industry practices and has complied with specific
recommendations of the Company. Accessories or equipment furnished
by the Company, but manufactured by others, shall carry whatever
warranty the manufacturers have conveyed to the Company and which
can be passed on to the Purchaser. The Company shall not be liable for
any repairs, replacements, or adjustments to the Equipment or any costs
of labor performed by the Purchaser or others without Company's prior
written approval.
The effects of corrosion, erosion and normal wear and tear are
specifically excluded. Performance warranties are limited to those
specifically stated within the Company's proposal. Unless responsibility
for meeting such performance warranties are limited to specified tests,
the Company's obligation shall be to correct in the manner and for the
period of time provided above.
THE COMPANY
MAKES NO OTHER WARRANTY
OR
REPRESENTATION OF ANY KIND WHATSOEVER, EXPRESSED OR
IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE HERBY DISCLAIMED.
Correction by the Company of nonconformities whether patent or latent,
in the manner and for the period of time provided above, shall constitute
fulfillment of all liabilities of the Company for such nonconformities
whether based on contract, warranty negligence, indemnity, strict liability
or otherwise with respect to or arising out of such Equipment.
The Purchaser shall not operate Equipment which is considered to be
defective, without first notifying the Company in writing of its intention to
do so. Any such use of Equipment will be at Purchaser's sole risk and
liability.
Note that this is Ingersoll Rand standard warranty. Any warranty in force
at the time of purchase of the equipment or negotiated as part of the
purchase order may take precedence over this warranty.
2.0 INTRODUCTION
3.0 WARRANTY
4.0 HEAT REACTIVATED DRYER NOMENCLATURE
NOMINAL
*
FLOW
POWER /
NEMA/
ELECTRICAL
ELECTRICAL
MECHANICAL
PREFIX
(SCFM)
DEW POINT
MAWP
OPTION
OPTION
OPTION
FILTERS
HB
150-8000
4 = 460-3-60 / -40
H = NEMA 4 /
0 = Standard
0 = Standard
0 = Standard
A = Filters Attached
6 = 575/3/60 / -40
150 psig MAWP
N = EMS
L = Filters Loose
*
Nominal Flows indicated are for 100°F inlet temperature, 100°F ambient temperature and 100 psig compressed air pressure.
120.26 Dryer - Operation, Installation, Maintenance Manual, and Parts
