4
SAFE OPERATING INSTRUCTIONS
The following warnings and operating instructions have been
adapted in part from American National (Safety) Standard
ASME B30.7 and are intended to avoid unsafe operating
practices which might lead to injury or property damage.
Ingersoll-Rand recognizes that most companies who use
winches have a safety program in force at their facility. In the
event that some conflict exists between a rule set forth in this
publication and a similar rule already set by an individual
company, the more stringent of the two should take precedence.
Safe Operating Instructions are provided to make an operator
aware of dangerous practices to avoid and are not necessarily
limited to the following list. Refer to specific sections in the
manual for additional safety information.
1.
Only allow people, trained in safety and operation of this
product, to operate and maintain this winch.
2.
Only operate a winch if you are physically fit to do so.
3.
When a “DO NOT OPERATE” sign is placed on the
winch, or controls, do not operate the winch until the sign
has been removed by designated personnel.
4.
Before each shift, the operator should inspect the winch for
wear and damage. Never use a winch that inspection
indicates is worn or damaged.
WARNING
Welded mountings
can fail.
Can cause severe
injury or death.
Do not weld, braze or
solder to winch.
71270813
WARNING LABELS AND TAG
Each unit is shipped from the factory with the warning labels
and tag shown. If the labels or tag are not attached to your unit,
order new labels and tag and install. See the parts list for the
part numbers. Labels and tag shown smaller than actual size.
5.
Never lift a load greater than the rated capacity of the
winch. Refer to nameplate attached to winch and to
“SPECIFICATIONS” section.
6.
Keep hands, clothing, etc., clear of moving parts.
7.
Never place your hand in the throat area of a hook or near
wire rope spooling onto or off of the winch drum.
8.
Always rig loads properly and carefully.
9.
Be certain the load is properly seated in the saddle of the
hook. Do not support the load on the tip of the hook.
10. Do not “side pull” or “yard”.
11. Always ensure that you, and all other people, are clear of
the path of the load. Do not lift a load over people.
12. Never use the winch for lifting or lowering people, and
never allow anyone to stand on a suspended load.
13. Ease the slack out of the wire rope when starting a lift or
pull. Do not jerk the load.
14. Do not swing a suspended load.
15. Do not leave a suspended load unattended.
16. Never operate a winch with twisted, kinked or damaged
wire rope.
17. Pay attention to the load at all times when operating the
winch.
18. Never use the wire rope as a sling.
19. After use, or when in a non-operational mode, the winch
should be secured against unauthorized and unwarranted
use.
WARNING
?
Read the latest edition of ASME B30.7.
Comply with other federal, state and local rules.
P/N 71056410/A
for winches
Failure to follow these
warnings may result in
death, severe injury or
property damage:
Do not operate
this winch before
reading operation
and maintenance
manual.
Do not lift people or loads
over people.
Do not lift more than rated
load.
Do not allow less than three
wraps of wire rope to remain
on drum at all times.
Do not operate a damaged
or malfunctioning winch.
Do not remove or obscure
warning labels.
Summary of Contents for FA2A
