background image

Upflow/Horizontal — Downflow/Horizontal, Gas-Fired Furnaces, 

“Fan Assisted Combustion System”

ALL phases of this installation must comply with

NATIONAL, STATE AND LOCAL CODES

IMPORTANT — This Document is customer property and is to

remain with this unit. Please return to service

information pack upon completion of work.

A341789P12

INSTALLER’S GUIDE

Upflow/ Horizontal*

Downflow/ Horizontal*

For VENT SIZING INFORMATION see:

USA —

National Fuel Gas Code  ANSI Z223.1/ NFPA 54 (latest version)

CANADA—

Natural Gas Installation Code 

CAN/ CGA-B149.1 (latest version)

Propane Installation Code  CAN/ CGA-B149.2 (latest version)

*Horizontal Conversion for these furnaces may be left 

or right side rotation.

18-CD34D1-5-EN

OPTIONAL ACCESSORIES

Model Number

Description

BAYBASE205

Downflow subbase for downflow models 

only

BAYFLTR200

External side filter rack

BAYFLTR203

Filter kit horizontal for 17.5" cabinet

BAYFLTR204

Filter kit horizontal for 21" cabinet

BAYFLTR205

Filter kit horizontal for 24.5" cabinet

BAYFLTR317

Cleanable filter for 17.5" cabinet upflow 

only

BAYFLTR321

Cleanable filter for 21" cabinet upflow 

only

BAYFLTR324

Cleanable filter for 24.5" cabinet upflow 

only

BAYLPKT210B

Propane conversion kit

BAYLPSS210B

LP kit with stainless steel burners

BAYRACK960A

Internals filter rack kit for upflow models

BAYVENT800B

Masonry chimney vent kit for upflow only

KIT09224

Filter clip kit

BAYBRCKFLT10

Downflow bracket kit

FLR01185

Filter for 14-1/2" cabinet downflow only

FLR01186

Filter for 17-1/2", 21", 24-1/2" cabinet 

downflow only

M801P040AU24AA
M801P060AU24AA
M801P060AU36AA
M801P080BU36AA
M801P080BU48AA 

M801P100BU36AA
M801P100CU48AA
M801P100CU60AA
M801P120DU60AA
M801P140DU60AA

M801P060AD24AA
M801P060AD36AA
M801P080BD45AA
M801P100CD48AA

M801P100CD60AA
M801P120DD60AA
M801P140DD60AA

Summary of Contents for M801P040AU24AA























Reviews: