background image

FOREWORD

2

UP6RD–5–175, UP6RM–5–175, UP6RD–5–175

The contents of this manual are considered to be proprietary and

confidential to Ingersoll–Rand and should not be reproduced without
the prior written permission of Ingersoll–Rand.

Nothing contained in this document is intended to extend any

promise, warranty or representation, expressed or implied, regarding
the Ingersoll–Rand products described herein. Any such warranties or
other terms and conditions of sale of products shall be in accordance
with the standard terms and conditions of sale for such products, which
are available upon request.

This manual contains instructions and technical data to cover all

routine operation and scheduled maintenance tasks by operation and
maintenance staff. Major overhauls are outside the scope of this
manual and should be referred to an authorized Ingersoll–Rand service
department.

All components, accessories, pipes and connectors added to the

compressed air system should be:
.

of good quality, procured from a reputable manufacturer and,

wherever possible, be of a type approved by Ingersoll–Rand.
.

clearly rated for a pressure at least equal to the machine maximum

allowable working pressure.
.

compatible with the compressor lubricant/coolant.

.

accompanied with instructions for safe installation, operation and

maintenance.

Details of approved equipment are available from Ingersoll–Rand
Service departments.

The use of non–genuine spare repair parts other than those

included within the Ingersoll–Rand approved parts list may create
hazardous conditions over which Ingersoll–Rand has no control.
Therefore Ingersoll–Rand cannot be held responsible for equipment in
which non–approved repair parts are installed. Standard warranty
conditions may be affected.

Ingersoll–Rand reserves the right to make changes and

improvements to products without notice and without incurring any
obligation to make such changes or add such improvements to
products sold previously.

The intended uses of this machine are outlined below and examples

of unapproved usage are also given, however Ingersoll–Rand cannot
anticipate every application or work situation that may arise.

IF IN DOUBT CONSULT SUPERVISION

.

This machine has been designed and supplied for use only in the
following specified conditions and applications:
.

Compression of normal ambient air containing no known or

detectable additional gases, vapors. or particles
.

Operation within the ambient temperature range specified in the

GENERAL INFORMATION section of this manual.

The use of the machine in any of the situation types listed in

table 1:–
a) Is not approved by Ingersoll–Rand,
b) May impair the safety of users and other persons, and
c) May prejudice any claims made against Ingersoll–Rand.

TABLE 1

Use of the machine to produce compressed air for:

a) direct human consumption
b) indirect human consumption, without suitable filtration and purity
checks.

Use of the machine outside the ambient temperature range

specified in the GENERAL INFORMATION SECTION of this manual.

Use of the machine where there is any actual or foreseeable risk of

hazardous levels of flammable gases or vapors

Use of the machine fitted with non Ingersoll–Rand approved

components.

Use of the machine with safety or control components missing or

disabled.

The company accepts no responsibility for errors in translation of

this manual from the original English version.

ALL SEASON SELECT is a registered trademark of
Ingersoll–Rand Company USA.

COPYRIGHT 2003

INGERSOLL–RAND COMPANY

Summary of Contents for UP6RD-5-175



























Reviews: