background image

INGICS

TECHNOLOGY

Guide

Ver.01c

BLE_WiFi Gateway

iGS01S User Manual

iGS01S is a bridge to connect the local BLE devices, sensors, or beacons to the internet by WiFi.
Through an easy web UI interface, one can configure the internet connection to a general cloud server,
like TCP, HTTP(S), or MQTT. Management through the cloud to the BLE devices becomes simple
through iGS01S. This guide is to help the user to figure out how to operate and configure the iGS01S.

Contents

Contents
Overview

Inside the box
WiFi
BLE

Input and Output

Multi-function button

WPS
Reset to Default
Firmware Upgrade

LEDs

Create Connection
Web User Interface

Wi-Fi

Simple AP
Station

Network

AP Client Setting
AP Server Setting

Applications

M2M TCP Server
M2M TCP Client
HTTP Client

Force HTTPS
Keep-Alive
Request Interval
Throttle Control

MQTT Client

MQTTS
Request Interval and Throttle Control, please refer to HTTP client.

Advanced

BLE Filter

RSSI
Payload Whitelist

Device Key/Certification Update

System

NTP setting

Waste Electrical and Electronic Equipment Recycling
Certification

Statement
CE Regulatory

Revision History

INGICS TECHNOLOGY CO., LTD.    •    JK.FAN@INGICS.COM •    WWW.INGICS.COM

1

Summary of Contents for iGS01S













Reviews: