15
EN
Handwash in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
• Dry the textile lining completely before using or storing it.
• To avoid any formation of mould, it is advisable to
periodically air the product out. In particular, separate the
textile lining from the frame and clean the base with a dry
cloth.
WARNING
LIST OF COMPONENTS
fig. 1
A
Tray
B
Removable
tray
C
Front feet with wheels
D
Rear
feet
FEET
fig. 2
To fasten the feet with wheels (
C
), place them in
correspondence of the front legs and push until the metal
peg (
F
) enters correctly into its housing.
fig. 3
Repeat the operation for both the rear feet (
D
).
OPENING
fig. 4
Stand behind the high chair and press the buttons
(
G
) on the right and on the left at the same time, hold the
chair as it opens until it locks in place with a Click.
fig. 5
Then lift the backrest, holding it until you here a
Click, indicating that it has been attached properly.
CAUTION! Before using the product, make sure that it is
fully open and blocked properly.
FOOTREST
fig. 6
The footrest (
E
) can be adjusted to 3 positions;
press both buttons (
J
) at the same time and accompany the
footrest to the desired position.
fig. 7
To lift the footrest (
E
), simply pull it upwards and it
shall automatically lock into position.
TRAY
fig. 8
To attach the tray (
A
), position it in line with the
armrests on the high chair and by acting on the lever (
H
)
under the tray, push it in the desired position.
CAUTION! Always verify that the tray is correctly hooked
before use.
After having hooked the tray (
A
), it is possible to adjust its
distance from the seat in order to be able to seat the baby
more easily.
fig. 9
Act on the lever (
H
) to put the tray in the desired
position.
fig. 10
The tray is equipped with an easily removable tray
(
B
) cover that can be washed even in the dishwasher.
fig. 11
If needed, the tray (
A
) can be easily put away by
hooking it onto the slots (
K
) located under the rear legs of
the high chair.
SEAT INCLINATION
It is possible to recline the high chair into 3 different positions.
fig. 12
Hold the (
L
) handle and incline the chair to the
wished position.
HEIGHT ADJUSTMENT
The high chair is designed with 4 different height
adjustments.
fig. 13
To lower the high chair, stand in front of it and by
acting on both levers (
M
) at the same time, move it into the
desired position.
fig. 14
To lift the high chair simply pull it upwards: it will
lock into place automatically.
SAFETY BELT
Verify that the safety belts are inserted in the eyelets at the
height of the shoulders or immediately above. If the position
is not correct, extract the belts from the first pair of eyelets
and reinsert them in the second one; always use eyelets at
the same height.
fig. 15
Make sure that the back strap is properly inserted in
the ends of the waist one.
fig. 16
Fasten the ends of the waist belt to the central
buckle.
fig. 17
Always use the crotch strap together with the waist
one, adjusting both of them properly.
CAUTION! The inobservance of this precaution may result
in the falling or sliding out of the baby with a resulting
risk of injury.
CLOSING
fig. 18
To close the high chair properly, adjust its height in
the highest position (
n° 1
).
In order to close it completely, the seat can be fully tilted
fowards.
fig. 19
Turn and push the button on the right hand side
(
N
) and at the same time press the button on the left hand
side only (
O
) moving the seat forwards.
fig. 20
Stand behind the high chair and press the buttons
(
G
) on the right and on the left at the same time, hold the
chair as it closed until it locks in place with a Click.
CAUTION! Never close the high chair with the baby in the
high chair!
fig. 21
Once closed, the high chair stays in the upright
position by itself.
MAINTENANCE OF THE LINING
It is recommended to remove the lining periodically to
provide for its correct maintenance.
fig. 22
Undo all the snap fasteners.
fig. 23
After having reclined the highchair completely,
remove the lining from the side of the arm rest.
fig. 24
Release the waist belt from the backrest frame
pipes being careful to remove it from the metal ring (
P
).
fig. 25
Once all belts have been fed through the slots, fully
remove the lining.
INSTRUCTIONS
Summary of Contents for Gusto Seggiolone
