background image

2

Warranty

Fire detection and extinguishant system

Warranty

INIM Electronics s.r.l. (Seller, Our, Us) warrants the original purchaser that this product shall be free from defects in 
materials and workmanship under normal use for a period of 24 months. As INIM Electronics s.r.l. does not install this 
product directly, and due to the possibility that it may be used with other equipment not approved by Us; INIM 
Electronics s.r.l. does not warrant against loss of quality, degradation of performance of this product or actual damage 
that results from the use of products, parts or other replaceable items (such as consumables) that are neither made nor 
recommended by INIM Electronics. Seller obligation and liability under this warranty is expressly limited to repairing or 
replacing, at Seller's option, any product not meeting the specifications. In no event shall INIM Electronics s.r.l. be liable 
to the purchaser or any other person for any loss or damage whether direct of indirect or consequential or incidental, 
including without limitation, any damages for lost profits, stolen goods, or claims by any other party caused by defective 
products or otherwise arising from the incorrect or otherwise improper installation or use of this product.

This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:

• damage arising from improper maintenance or negligence
• damage caused by fire, flood, wind or lightning
• vandalism
• fair wear and tear

IINIM Electronics s.r.l. shall, at its option, repair or replace any defective products. Improper use, that is, use for purposes 
other than those mentioned in this manual will void the warranty. Contact Our authorized dealer, or visit our website for 
further information regarding this warranty.

Limited warranty

INIM Electronics s.r.l. shall not be liable to the purchaser or any other person for damage arising from improper storage, 
handling or use of this product.

Installation of this Product must be carried out by qualified persons appointed by INIM Electronics. Installation of this 
Product must be carried out in accordance with Our instructions in the product manual.

Copyright

The information contained in this document is the sole property of INIM Electronics s.r.l.

No part may be copied without written authorization from INIM Electronics s.r.l.

All rights reserved.

Summary of Contents for PREVIDIA MAX





















Reviews: