background image

22 

MSV0502 OPERATION MANUAL  -  v1.0  4/26/02 

 2002 - INLINE, INC. 

Warranty 

 

• 

INLINE warrants the equipment it manufactures to be free from defects in materials and 
workmanship. 

 

• 

If equipment fails because of such defects and INLINE is notified within three (3) years from the 
date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided 
that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. 

 

• 

Equipment that fails under conditions other than those covered will be repaired at the current price of 
parts and labor in effect at the time of repair.  Such repairs are warranted for ninety (90) days from 
the day of re-shipment to the Buyer. 

 

• 

This warranty is in lieu of all other warranties expressed or implied, including without limitation, 
any implied warranty or merchantability or fitness for any particular purpose, all of which are 
expressly disclaimed. 

 

The information in this manual has been carefully checked and is believed to be accurate.  
However, INLINE, Inc. assumes no responsibility for any inaccuracies that may be 
contained in this manual.  In no event will INLINE, Inc. be liable for direct, indirect, 
special, incidental, or consequential damages resulting from any defect or omission in this 
manual, even if advised of the possibility of such damages.  The technical information 
contained herein regarding the MSV0502 features and specifications is subject to change 
without notice. 
 
Windows is a registered trademark of Microsoft Corporation.  All other trademarks and 
registered trademarks are the property of their respective companies. 
 

All Rights Reserved  © Copyright 2002 INLINE, Inc. 

 
 

 

© INLINE, Inc.  •  810 WEST TAFT  •  ORANGE, CA  92865 

 

(800) 882-7117  •  (714) 450-1800  •  Fax:  (714) 450-1850  •  www.inlineinc.com 

 

 

Summary of Contents for MSV0502



























Reviews: