background image

IF44

IF44 Rod Box Installation Instructions

Before using this product, carefully read this instruction manual for proper use.
Keep this instruction manual in a safe place.
If you are to give this product to a third person, provide him/her with this manual as well 
to ensure safe use.

●This product is made specifically for fishing rods and those with reels attached. 

  Do not use for other purposes.

●Do not modify this product.

●Avoid overspeeding, sudden starts, sudden turns, and sudden braking as much as possible. 

●Close the cover securely and lock with the key. Failing to do so may cause the cover to open while 

  driving, and the rod box to be damaged and/or to fall off the vehicle roof due to wind pressure. 

●Before driving, check the two installation positions with the base carriers, and the bolted positions on 

  the product body are securely tightened. Re-tighten all loosely-bolted positions.

●Make sure that the vehicle rear hatch (trunk) does not hit the rod box when opening.

●The rod box is not constructed to be completely waterproof. 

  Loaded items may get wet due to strong rain.

●Opening and closing the rod box during strong gusts or winds may cause the box to be damaged, 

  or have your body trapped in the box, leading to injury.

●Always remember that the vehicle height has increased when the rack is installed.

●Remove the rack before using an automatic car wash.

●Do not use a car cover (including a cover for preventing paint splatter) with this product installed. 

  The rod box may deform due to weather conditions such as high temperatures.

●Do not place any items on this product. Doing so may cause cover deformation.

●The rod box materials gradually deteriorate due to exposure to UV light. If you do not plan to use the rod 

box for a long period of time, store it away from direct sunlight, high temperature, and high humidity. 

Failure to follow this warning can result in serious accidents including death or serious injury.

Failure to follow precautions can result in injury, damage to the product, vehicle, or load.

Before using this product, the followings should be noted.

−1−

5590627A

Warning

Precautions

Note

Summary of Contents for IF44













Reviews: