1x Clearomiseur P16A
1x Résistance Organic Cotton Coil for 14 Series 1,6 Ohm | MTL
1x mode d‘emploi
1x carte d‘informations
Contenu de la livraison | Structure de l‘appareil
Base de tête d’atomiseur
Embout buccal
Tête d‘atomiseur
Airflow
Control
Réservoir
Utilisation de l‘appareil
Pour nettoyer l‘appareil, utilisez un chiffon sec ou un coton-tige.
Instructions de nettoyage
Pendant que vous maintenez enfoncée la touche d‘allumage de votre batterie, inhalez la vapeur lentement et en continu via l‘embout de
votre clearomiseur. Relâchez le bouton fire pendant que vous expirez la vapeur.
Vapoter
En tournant légèrement le réservoir, vous augmentez ou réduisez le débit d‘air selon vos préférences personnelles. Plus le débit d‘air est élevé
(donc plus les fentes de passage d‘air sont ouvertes), plus la résistance à l‘aspiration diminue.
Précautions d‘utilisation :
Avant la première utilisation, déposez impérativement quelques gouttes de votre liquide sur la tête d‘atomiseur (head) et, après l‘installation,
laissez-la reposer environ 15 minutes dans le réservoir rempli de liquide avant de vapoter. Pour cela, posez le clearomiseur la tête en bas. Ne
nettoyez pas la tête d‘atomiseur à l‘eau. En cas de besoin, essuyez-la seulement avec un chiffon sec. Les têtes d‘atomiseur étant des pièces d‘usure,
elle doivent être changées régulièrement.
Régler l‘alimentation d‘air
Le clearomiseur est équipé d‘une sécurité enfants.
1. Gardez une pression sur la tête d’atomiseur et dévissez la en tournant le
réservoir dans le sens inverse des aiguilles d‘une montre pendant que
l‘embout buccal est orienté vers le bas.
2. Remplissez le clearomiseur de liquide en utilisant la fente de remplissage. Veillez
impérativement à ce que le liquide ne pénètre pas dans le canal d‘air médian.
3. Afin de refermer le récipient, revissez la base de la tête d’atomiseur sur ce
dernier. Pour ceci, appuyez sur les composants pendant que vous revissez.
Assurez-vous qu‘aucun liquide ne puisse en sortir.
1. Retirez le clearomiseur de la batterie de votre cigarette électronique.
2. Faites-le tourner de manière à ce que l‘embout soit orienté vers le sol.
Retirez la base de la tête d‘atomiseur à réglage d‘airflow en tournant le réservoir en verre de l‘appareil.
3. Retirez la tête usagée en la dévissant et remplacez-la par une nouvelle en la revissant.
4. Pour finir, remontez toutes les pièces ensembles et veillez à ce que le liquide ne puisse pas déborder.
Remontez le clearomiseur sur la batterie et laissez à la tête suffisamment de temps pour s‘imbiber de liquide.
Remplissage avec le liquide
Changement de la tête d‘atomiseur
Volume du réservoir
1,9 ml
Diamètre
16 mm
Hauteur (embout buccal inclus) 54 mm
Matières
Polycarbonate, laiton chromé
Type de fil résistif
510
Système de remplissage par le bas
Airflow Control (système de régulation du débit d‘air)
Tête JustFog 1,2 Ohm, Tête JustFog 1,6 Ohm
Convient uniquement à une utilisation avec une batterie résistant aux courants de forte intensité !
Dimension de
l‘ouverture du
réservoir de liquide
Informations principales Clearomiseur P16A
Fonctions
Têtes d‘atomiseur adaptées
Données clés et caractéristiques de performance
4
mm
Le produit JustFog-que vous avez acheté a été importé pour vous par InnoCigs GmbH & Co.
Si le produit ne fonctionne pas ou présente la moindre défectuosité, veuillez contacter directement le revendeur spécialisé auprès duquel vous l‘avez
acheté. Pour toutes questions sur le fonctionnement et l‘utilisation de votre appareil, n‘hésitez pas à contacter notre service client.
N‘utilisez en aucun cas l‘appareil en le combinant avec des produits d‘autres fabricants, mais uniquement avec des produits JustFog pour lesquels
il est indiqué qu‘ils conviennent à cet appareil. Nous vous rappelons expressément que nous déclinons toute responsabilité concernant les dom-
mages survenant à la suite d’une utilisation non-conforme du produit et que, dans ce cas, sa garantie devient caduque.
Conditions de garantie de la société InnoCigs GmbH & Co. KG
Garantie et service après-vente
InnoCigs GmbH & Co. KG
Téléphone : +49 (0)40 22 86 729 0
Stahltwiete 23
Fax : +49 (0)40 22 86 729 99
22761 Hambourg | ALLEMAGNE
E-Mail : service@innocigs.com
Contact de votre importateur JustFog officiel
Contact d’InnoCigs
1. If the device has been dropped, please check if any components have come loose, whether there is liquid leakage, or whether there is any defect on your
mouthpiece. If there are no signs of damage upon visual inspection of the product, you can continue using the device. For hygienic reasons, please wipe
the mouthpiece with a cloth before reusing.
2. The device should not be used if there are cracks or deformations in the material or a defective part needs to be replaced. Never attempt to repair the
device on your own if a defect occurs.
3. The device should not be used when the e-liquid in the clearomizer tank is empty or almost empty. The same applies if you experience a change in the
taste. Please fill the Clearomizer tank with fresh e-liquid and replace the head before you continue to use the e-cigarette. Because atomizer heads are
wearing parts, they must be changed regularly.
4. Never store the device in rooms with extremely high temperatures or in rooms with extremely high humidity. Avoid long periods of direct sunlight.
5. The recommended temperature range for charging is 5°C to 45°C and for using the device is -10°C to 60°C.
6. If e-liquid comes in contact with your skin, wipe it off as soon as possible and wash the area of contact.
7. If e-liquid is swallowed, contact your local poison control center. The Poison Emergency Hotline of the Charité University Hospital Berlin can be reached
day and night by phone at +49 (0)30 - 19 240. In Austria, you can reach the 24h hotline of the Vienna Poison Information Center by phone at +43 (0)1 -
406 43 43. In France, please contact one of the local poison control centers. In case of emergency, immediately contact local emergency officials.
8. Nicotine can increase the heart rate and/or blood pressure. Nicotine can cause nausea, dizziness and/or stomach pain. If you notice any undesirable side
effects, discontinue use and consult a physician.
9. Please comply with all local laws when using this e-cigarette product.
10. The product must not be placed in the hands of children or adolescents.
User Instructions
JustFog P16A Clearomizer
English
This e-cigarette product can be used with nicotine-containing e-liquid. Nicotine is a highly addictive substance.
When vaping, a distinction is made between two puffing techniques:
Moderate Vaping (Mouth-to-Lung)
The vapor from an e-cigarette is first collected in the oral cavity for the entire duration of the puff and then inhaled into the lungs. This puffing
technique is referred to as moderate, mouth-to-lung vaping and is similar to smoking. To achieve this, there must be a noticeable resistance when
puffing on the e-cigarette. Evaporator heads that support this puffing technique in the moderate range (resistance usually > 1 ohm) are often
referred to as MTL (mouth to lung) heads. (Other abbreviations include ML and M2L)
Sub-Ohm Vaping (Direct Lung Inhalation)
While puffing, the vapor of an e-cigarette is directly inhaled into the lungs. This puffing technique is referred to as sub-ohm vaping with direct lung
inhalation. To achieve this, there must be low puffing resistance and a strong air supply to the evaporator head. Both have a positive effect on pro-
ducing large quantities of vapor. Evaporator heads that support this puffing technique in the sub-ohm range (resistance usually < 1 ohm) are often
referred to as DL (direct lung) heads. (other abbreviations include DTL and D2L)
Warning
General Information about Puffing Techniques while Vaping
1 x J-Easy3 Battery
1x P16A Clearomizer
1x Organic Cotton Coil for 14 Series Head 1.6 Ohm | MTL
1x User Manual
1x Info Card
Contents | Design of the Device
Atomizer head base
Mouthpiece
Atomizer head
Airflow
Control
Tank
Using the Device
Use a dry cloth or cotton swab to clean the device.
Tips for Cleaning
While holding the fire button of your e-cigarette, inhale the vapor slowly and continuously through the mouthpiece of your clearomizer.
Release the Fire button when exhaling the vapors.
The clearomizer is equipped with a child safety lock.
1. Hold the atomizer head base down and screw it off of the tank by twis-
ting it counterclockwise with the mouthpiece facing toward the ground.
2. Add your e-liquid into the clearomizer through the filling hole. Please
make sure that no e-liquid ends up in the air duct at the center.
3. To close it, screw the atomizer head base back onto the tank. To do so,
press the components downward as you twist it on. Make sure that no
e-liquid can escape.
1. Loosen the clearomizer from the battery of your e-cigarette.
2. Turn it so that the mouthpiece faces the floor. Remove the atomizer head base with airflow control by twisting the glass tube section of the
device.
3. Remove the old atomizer head by twisting and insert a new one, screwing the new one on.
4. Then reconnect all parts and make sure that no e-liquid can leak out. Screw the clearomizer back onto the battery and give the new atomizer
head enough time to suck up a sufficient amount of e-liquid.
Vaping
Filling with E-Liquid
Switching the Atomizer Head
Please note the following:
Prior to first use, drip a few drops of your e-liquid on the atomizer head and let it sit in the liquid-filled tank for around 15 minutes after installation
before you start vaping. To do this, please turn the clearomizer upside down. Don’t clean the atomizer head with water. If necessary, simply wipe
with a dry cloth Since atomizer heads are disposable, they must be replaced regularly.
You can increase or reduce the air supply just as you like it by lightly twisting the tank. The more air flows through the device
(the more the slots are open), the lower is the drawing resistance.
Adjusting the Air Supply
Thank you for choosing this e-cigarette product from JustFog! We place great value on high quality and safety standards across our entire range. We
hope you enjoy vaping with your new e-cigarette product! Read the operating instructions carefully before use in order to ensure correct use of the
device. Use only original and/or recommended products in combination with this product. InnoCigs GmbH & Co. KG, as the official importer of this
JustFog product, does not provide any service and/or warranty when non-recommended products are used together with this product.
Should you have questions or need more information about your device, please contact your dealer or visit our website at www.innocigs.com.
Information for the User
Tank volume
1.9 ml
Diameter
16 mm
Height (incl. mouthpiece) 54 mm
Material
Polycarbonate, chrome-plated brass
Thread type
510
Bottom filling system
Airflow control
JustFog head 1.2 ohms, JustFog head 1.6 ohms
Only for use in combination with high-current batteries and box mods!
Dimension of the
e-liquid tank opening
Key Features of the P16A Clearomizer
Features
Suitable Atomizer Heads
Key Features & Performance
4
mm
Notes & Precautions
Persons under 18 years, pregnant women, nursing mothers and people with cardiovascular disease should not use this product. Not recom-
mended for non-smokers. Please keep out of the reach of children.
This product must not be
used by minors.
This product must be kept away
from children.
This product must not be
used by pregnant or nursing
women.
This product complies with EU require-
ments on technical goods and may be
sold throughout the European Union.
Electronic goods and batteries should not be disposed with
normal household waste! Please dispose of used electronic
goods and batteries – as required by law – at a municipal collec-
tion location, so that raw materials and potentially harmful
substances can be properly removed and recycled.
The JustFog product you have just purchased was imported for you by InnoCigs GmbH & Co. KG. If the product ceases functioning or is defective
in any way, please contact the specialist retailer where you purchased the product. Please feel free to contact our customer service department
with any questions concerning operation and use of the device.
Please do not use products from other manufacturers in combination with your device and only use products that are marked as suitable for use
with JustFog products. We expressly point out that we cannot accept liability for damages that occur if the product is used improperly, and that in
such a case the product warranty will be void.
InnoCigs GmbH & Co. KG
Phone: +49 (0) 40 – 22 86 729 0
Stahltwiete 23
Fax: +49 (0) 40 – 22 86 729 99
22761 Hamburg | GERMANY
E-Mail: service@innocigs.com
Warranty Terms of the InnoCigs GmbH & Co. KG
Contact your official JustFog importer
Warranty & Service
Contact to InnoCigs
