background image

Page 7

 

   

 

USER MANU

AL   SMR-31

3 / 332 / 333

  

Version 2.0

 

  

CONFIDENTIAL AND PROPRIETARY

The information contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall not be 

disclosed by the recipient to third parties without prior consent of InnoSenT in writing.

Experience and Reliability in Radar Technology

www.InnoSenT.de

SMR

Annex A

The information that will be given below is only a rough overview; for details please contact the local approval 
agencies. An overview over the frequency bands in Europe can also be found in the REC 70-03 (Annex 6) which is 
available under www.ero.dk

 

24.000

24.250

For the US-market the SMR-3X3 can be used

US-frequency

FCC approval

This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)].
Operation is subject to the following two conditions:
           (1) this device may not cause harmful interference, and
           (2) this device must accept any interference received, including interference that may cause undesired  
                operation.

Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void 
the FCC authorization to operate this equipment.

Manufacturers of mobile or fixed devices incorporating SMR-3X3 modules are authorized to use the FCC Grants 
of the SMR-3X3 modules for their own final products according to the conditions referenced in these documents. 
In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second 
label stating „Contains FCC ID: UXS-SMR3X3 “ 

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et 
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep-
tible d’en compromettre le fonctionnement.

NOTICE:
Changes or modifications made to this equipment not expressly approved by (manufacturer name) may void the 
FCC authorization to operate this equipment.

Fr

equency Bands in US

 FCC 15.249

Summary of Contents for SMR-313










Reviews: