innovair 18K User And Installation Manual Download | Manualshive

Page: 16 / 17

background image

14

Installation instructions

The air-conditioner is provided with a crankcase heater, check to ensure that the switch on the main
power source has been ON for more than 6 hours ahead of power on preheating, otherwise it might
damage the compressor!

Turn off the power

after trial run is finished.

Installation of the appliance is generally finished after the above operations are done. If you still have any trouble,
please contact local technical service center of our company for further information.

CAUTION

Trial

Run

«
...
14
15
16
17
»

Summary of Contents for 18K


















Reviews:

No comments

Related manuals for 18K

Temovex RT 400S-EC

Brand: REC Pages: 48

Brand: TemperZone Pages: 9

Brand: XPower Pages: 24

e-MovAir Series

Brand: Lennox Pages: 28

Brand: Remington Pages: 24

Brand: Reznor Pages: 33

Brand: York International Pages: 2

Brand: TCF Pages: 63

Brand: flakt woods Pages: 28

Brand: Vents Pages: 16

Brand: Daikin Pages: 16

Brand: United Technologies Pages: 60

Brand: Daikin Pages: 15

Brand: Daikin Pages: 24

Brand: Daikin Pages: 24

Brand: Daikin Pages: 126

Modular L Smart

Brand: Daikin Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands