background image

28

Installation of indoor unit

Step eight: bind up pipe

1. Bind up the connection pipe, power
    cord and drain hose with the band.

indoor unit

gas
pipe

indoor and

outdoor power cord

liquid pipe

drain hose

band

2. Reserve a certain length of drain

hose and power cord for installation
when binding them. When binding to
a certain degree, separate the indoor
power and then separate the drain
hose.

3. Bind them evenly.
4. The liquid pipe and gas pipe should

be bound separately at the end.

Note:

● The power cord and control wire

can't be crossed or winding.

● The drain hose should be bound

at the bottom.

drain hose

band

connection pipe

indoor power cord

Step nine: hang the indoor unit

1. Put the bound pipes in the wall pipe and then make them pass through the wall

hole.

2. Hang the indoor unit on the wall-mounting frame.
3. Stuff the gap between pipes and wall hole with sealing gum.
4. Fix the wall pipe.
5. Check if the indoor unit is installed firmly and closed to the wall.

Note:

● Do not bend the drain hose too excessively in order to prevent blocking.

indoor

outdoor

wall pipe

sealing gum

upper hook

lower hook of
wall-mounting frame

©2015 Innovair Corporation.  All Rights Reserved.

www.innovair.com

Summary of Contents for VWM10H25





































Reviews: