Innovative NV200 Operation Manual Download

Page: 3 / 32

1 INTRODUCTION

This manual describes the operation of the NV200 Bank Note Validator, programmed with

Firmware Version 4.04 or greater.

This document is intended for those who will:

•

Install the NV200 equipment.

•

Maintain the NV200 equipment

Although information is included which will allow a degree of fault diagnosis and repair, it

is recommended that for all but simple mechanical repairs, the unit must be returned to

an approved service centre for repair.

For more concise information, addressed primarily to maintenance, please refer for the

concise manual in our website.

CAUTIONS

•

Never exceed the recommended environmental and electrical limits.

•

Do not attempt to lubricate the mechanisms as this may affect the note transport.

•

Do not polish the lens as this may alter the optical characteristics.

•

If the NV200 validator is disassembled the unit must be re-initialised, following

assembly using LB149 initialisation paper from ITL.

WARNING

•

Only suitably trained personnel should carry out any work on this equipment in

accordance with all current local, national and international health and safety

regulations.

We recommend that you study this manual as there are many new features permitting new

uses and more secure applications. If you do not understand any part of this manual please

contact your local office for assistance, contact details are available from

www.innovative-

technology.co.uk

. In this way we may continue to improve our product.

The NV200 Validator has been designed to minimise any performance variation over time.

Much of this is achieved by careful Hardware and Software design. Innovative Technology Ltd

has a policy of continual product improvement. As a result the products supplied may vary

from the specification described here. This manual can be printed in A4 or letter sizes.

MAIN HEADQUARTERS

Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ

Tel: +44 161 626 9999 Fax: +44 161 620 2090

E-mail: support@innovative-technology.co.uk

Web site: www.innovative-technology.co.uk

NV200 Operations Manual

Summary of Contents for NV200

































Search results

Summary of Contents for NV200

Reviews:

Related manuals for NV200

Brands by name

Popular brands

Innovative NV200, Operation Manual

Search results

Summary of Contents for NV200

Reviews:

Related manuals for NV200

Brands by name

Popular brands