background image

                                                                                                                                                          insigniarange.com

 

Last Modified: 08/02/2018

 

 13 

Step 5 

 

Silicone

 specified as shown in diagram. 

 

Next using the angled upright, place this to the rear squared glass panel by follow-

ing the position shown in the image marked 

“1”

 

Now move the angled upright in the direction as shown in image 

“1” 

until this is into 

place as shown in image 

“2”

 

Once you are happy with the alignment then continue to screw the upright into 

place at the top and bottom using 

ST14

s

 

Please note: These are not pilot holed and you will need to use the DB6

 

1

 

2

 

1

 

2

 

 

1

 

2

 

Step 4

 

Now lock the front angled glass panel to the side glass panel by following 

the position shown in the image marked 

1

 

Once you have met the back panel inside the front upright as per the close 

up image walk the panel around to the position shown in the image 

marked 

2

 

NOTE: 

Do 

not 

apply silicone until Step 6

 

Step 4

 

Step 5

 

Summary of Contents for INS8058R


































Reviews: