background image

                                                                                                                                                          insigniarange.com

 

Last Modified: 27/01/2017

 

 16 

Step 10

 

 

Insert remaining upright to the left of the curved glass panel. Drill and screw this 

into position using the 

ST20 

screws

 

and once fixed slide the flat rubber glass seal into 

this newly fitted upright on the inside (as of the green line in the image)

 

Please Note

: ensure you drill no deeper than 5mm.

 

Step 11

 

 

Pierce through the holes using a screwdriver to show pre

-

cut holes in the glass as 

indicated in the image. Now using the chrome 

L

” 

brackets, fix these to the outside of the 

glass panels using the provided nuts and bolts (

B22

) please ensure the bolt goes 

through the plastic cover holder (

PCH13)

 first

 

Align the shower panels until you are happy with the sitting of these and now using the 

ST25 

screws, screw the brackets to the tub

 

Now place the Chrome cover caps (

CPC16

) onto the cover holders (

PCH13

)

 

Step 10

 

Step 11

 

Back

 

Inside

 

Summary of Contents for INS8059R


































Reviews: