Quick Cool
Quick Cool
QUICK SETUP GUIDE
1-Tap Beverage
Cooler / Kegerator
NS-BK1TBK8
Congratulations on your purchase! Your NS-BK1TBK8 kegerator is designed for
years of fun and trouble-free performance. This
Quick Setup Guide
is provided to
help you get your kegerator up and running quickly.
If you need more help,
however, take a look at the online manual, located at
www.insigniaproducts.com.
PACKAGE CONTENTS
1
Beer tap handle
2
Draft arm assembly
3
Guard
rail
4
Drip tray (2 pieces)
5
Worktop
6
Control
Panel
7
Sankey Type-D keg coupler
8
CO
2
tank regulator
9
5 lb. CO
2
tank (shipped empty)
10
Bolt and nut for retainer
11
CO
2
tank retainer
12
CO
2
gas line
13
Beer keg (not included)
14
Metal washers for locking casters (2)
15
Locking casters (2)
16
Beer gasket
17
Hose clamp
18
CO
2
back tank retainer
19
Extra valve washers
20
Wire shelf
21
Wire half-shelf
22
Metal wrench (for cleaning)
23
Casters (2)
Before assembly
Assembling your kegerator
INSTALLING THE CASTERS (OPTIONAL)
1
Tip the kegerator onto its side on a soft surface to protect it from
scratches.
2
Unscrew and remove the black front feet. Keep them in a safe place in
case you want to use the feet later.
3
Attach the two metal washers (included) to the locking casters to
prevent scratching the cabinet, then install the two locking casters in the
front positions on the bottom of the kegerator (closest to the door).
4
Install the other two casters in the rear positions on the bottom of the
kegerator.
5
With all four casters tightened evenly, stand the unit in the upright
position.
6
Step on the front of the locking casters to lock the kegerator into place
or step on the back to unlock the kegerator.
ATTACHING THE GUARD RAIL
Place the guard rail into the holes on the top of the kegerator.
INSTALLING THE DRAFT ARM ASSEMBLY
1
Remove the cabinet plug from the top of the kegerator.
2
Align the beer gasket with the holes on the top of the cabinet.
3
Pass both the wing nut and the beer tube (both are attached to the
draft arm assembly) through the hole on the worktop until the draft
arm assembly is resting on the top of the cabinet.
4
Rotate the draft arm 60 degrees until the tap is facing the front. It may
take some force.
5
Attach the black plastic beer tap handle to the top of the faucet,
tightening it by hand until it's secure. Hold the silver ring snug so it
does not move.
INSTALLING
THE
CO
2
REGULATOR & TANK
Note
: The CO
2
tank (provided) is empty when you receive it. Visit your local beer keg
provider, air/gas or welding supplier, or sporting goods store to get it filled.
Caution
: Before installing the CO
2
regulator and tank, review important safety tips in
the manual.
1
Feed the hose clamp over one end of the CO
2
gas line.
2
Attach that end to the gas line connector on the CO
2
regulator.
3
Tighten the clamp to prevent leaks. Leave about ½ inch between the
top of the clamp and the end of the hose. You may need to squeeze
with a pliers or crimper.
4
Attach the CO
2
regulator to the CO
2
tank by screwing the regulator
nut onto the tank valve and tightening with an adjustable wrench.
5
Slide the CO
2
tank through the retainer inside the kegerator and
secure it with the bolt and nut. Position the tank so that you can read
the numbers on the gauge and have easy access to the shut-off valve.
OR
Install the CO
2
tank retainer on the back of the kegeratorcoole for
extra space inside the unit. Refer to the manual for additional
information.
1
2
3
4
Fill the CO
2
tank
See your local beer keg
provider, air/gas or
welding supplier, or
sporting goods store.
Allow for space
Make sure that there
is 3” between the
back and sides of the
kegerator and any
surrounding walls.
Find a suitable location
Position the kegerator away from direct
sunlight and sources of heat, and avoid
positioning the kegerator in moist areas.
Do not use an
extension cord
You will need
3”
Adjustable
Wrench
Phillips
screwdriver
Full keg of beer
(1/2 barrel size
or smaller)
Pliers/
clamp crimper
Beer gasket
Wing nut and beer tube
Draft arm assembly
Beer tap handle
Sankey keg
coupler
Hose clamp
Shut-off valve
CO
2
gas line
Locking casters
Metal washers
Casters
Tank
valve
Regulator
nut
Flat size (W×H): 17.36 × 16.54 in. (440.9 x 420.1 mm)
Final folded size: 5.78× 8.27 in. (146.8 x 210 mm)
Before using your new product, please read these instructions to prevent any damage.
Front
Quick
Cool
CO
2
tank regulator
Adjust
temperature
Change
temperature unit
Display
Quick cool
Quick Cool
NS-BK1TBK8_17-0158_QSG_V2_EN.ai 1 2/17/2017 4:56:27 PM
NS-BK1TBK8_17-0158_QSG_V2_EN.ai 1 2/17/2017 4:56:27 PM
