Inspiration IP-S4305, Installation Instructions Use And Care Manual

Page 3

INSTALLATION INSTRUCTIONS

1

• TORQUE WRENCH 

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •• • • • • • •

1

• 8MM HEX KEY SOCKET  

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •

• #2 CROSS-HEAD (PHILLIPS) SCREWDRIVER 

• • • • • • • • •

1

1

• 6MM HEX KEY SOCKET  

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •

1

• 13MM SOCKET 

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •• • • • • • • • • • • •

1

• 5MM HEX KEY SOCKET  

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •

1

• 19MM OPEN-END WRENCH 

• • • • • • • • • • • • • • • • • • •• • • • • • • • • •

1

• 4MM HEX KEY SOCKET  

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •

1

• 17MM OPEN-END WRENCH 

• • • • • • • • • • • • • • • • • • •• • • • • • • • • •

1

• 3MM HEX KEY SOCKET  

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •

2

• 13MM OPEN-END WRENCH  

• • • • • • • • • • • • • • • • • • •• • • • • • • • •

1

• 2.5MM HEX KEY SOCKET  

• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • •

REQUIRED TOOLS:

GENERAL NOTES:  

•

Unless otherwise noted Loctite 242/243 or equivalent thread locker must be used on all threaded fasteners. (Do not 
use thread locker when a Nyloc nut is used.)

•

All Star Trac Strength equipment MUST be secured to the floor using either 10mm or 3/8in.  (grade 5 minimum) bolts.
To accommodate this there are four mounting points inside the weight stack and one in either of the small feet. 

•

This Installation Instructions Manual must be used in conjunction with the equipment’s Owner’s Manual.  The Owner’s 
manual describes equipment setup and instructs members on how to use it correctly and safely.

•

The Shoulder Press Machine weighs approximately 335 Kg (738 lbs) when fully assembled and occupies an area 148 
cm wide by 149 cm deep.  Star Trac recommends the addition of 1-2 people during assembly, and when moving the 
equipment to its designated point of use.  

Should any component not be present or if you have any operational questions, please refer to your owner’s manual or on 
the web @ 

www.startrac.com

. Specifically refer to your Inspiration serial number and model number labeled on your 

equipment.

THREAD LOCKER APPLICATION: 

Clean all threads and holes, apply no more than 3-4 drops per bolt.

Thru Holes

Blind Holes

PACKAGING REMOVAL:

Carefully remove all packaging materials that wrap the equipment. 

DO NOT USE A KNIFE OR BOX 

CUTTER AS YOU MAY DAMAGE THE EQUIPMENT. 

At this time remove any sub-components 

from the pallet and set aside for later assembly.   

• Torque all hardware to values as specified above, unless noted otherwise.
• See Page 9 of this manual for fastener sizing information; for reference only.
• Note: All torque values are in N-m unless otherwise stated.

26 to 30 (35 to 40)

1.75

10mm

9.5 to 12 (13 to 16)

1.25

8mm

4.5 to 6 (6 to 8)

1.25

6mm

Torque, N-m (lbs-ft)

Thread Pitch

Bolt Size

Metric Steel Bolts Torque Specifications