background image

3

 

 

IMPORTANT SAFETY NOTICE 

 

PRECAUTIONS 

 

This exercise machine is built for optimum safety.    However, certain precautions apply whenever you operate a piece of exercise equipment.    Be 

sure to read the entire manual before you assemble or operate your machine.    In particular, note the following safety precautions:  

1.  

Keep children and pets away from the machine at all times.  DO  NOT   leave  children unattended in the same room with the 

machine.    The linkages on this machine can cause serious injury if used improperly. 

 

2.        Never place your hands or feet in the path of the linkages because injury may occur to you or damage may occur to the equipment.   Never 

allow  children to come near or approach the moving linkages while in use.   

3.        Always engage the CHILD SAFETY LOCK after use.   

4.    If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once.    CONSULT A PHYSICIAN 

IMMEDIATELY. 

5.      Position the machine on a clear, leveled surface.    DO NOT use the machine near water or outdoors.   

6.      Keep hands away from all moving parts.   

7.      Always wear appropriate workout clothing when exercising.    DO NOT wear robes or other clothing that could become caught in the machine.         

Running or aerobic shoes are also required when using the machine.   

8.    Use the machine only for its intended use as described in this manual.    DO  NOT use attachments not recommended by the manufacturer.  

9.      Do not place any sharp object around the machine.   

10.      Disabled persons should not use the machine without a qualified person or physician in attendance.   

11. Before using the machine to exercise, always do stretching exercises to properly warm up.   

12. Never operate the machine if the machine is not functioning properly.   

13. Maximum user weight 300 lbs.   

 

 

CARE AND MAINTENANCE 

 

1.      Keep seat slider clean     

2.      Inspect and tighten all parts before using the machine.   

3.      Keep objects away from the fan area.      Never stick anything inside the fan grill. 

3.      The Frame, Shrouds and Seat Pad of the machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents.   

 

WARNING:    BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY 

IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS.    READ ALL 

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.  NEITHER HEALTH IN MOTION, LLC. NOR FG1, LLC. ASSUME 

ANY RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS 

PRODUCT. SAVE THESE INSTRUCTIONS. 

 

   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for CBI

























Reviews: