background image

GENERAL INFORMATION

SAFETY INFORMATION

1. The Max user weight is 120KGS

2. Always keep children and pets away from this device.

3. This device can be used only by one person at a time.

4. This device is not suitable for therapeutic purposes!

5. Please read this user manual before using this device.

6. If the use of this device causes dizziness, nausea, chest pain, or other unusual symptoms immediately

STOP exercising and contact a physician immediately.

7. Use this device only on clean and level surfaces.

8. Wrong and excessive exercise may be a danger to your health.

9. Use stretching exercises to warm up before using this device.

10. Always  wear appropriate athletic wear while exercising with this device. Never wear clothing that

might get caught by the device.

11. Exercise devices are not suitable toys.

WARNING: Always go to the doctor before starting a training program for all ages, especially if you are over 35
years of age or with pre-existing health conditions. Read all instructions before using an exercise device.

BATTERY INFORMATION

1. Never recharge batteries! Danger of explosion!

2. Keep   batteries   away   from   children,   do   not   throw   batteries   into   open   fire,   short-circuit   them   or

disassemble batteries.

3. Immediately remove empty batteries from the device increased risk of leakage!

4. Remove batteries from the device if it is not used for a long period of time.

3

Summary of Contents for IN 9101























Reviews: