background image

 

 

SAFETY INSTRUCTIONS 

 

To ensure the best safety of the exerciser, regularly check it on damages and worn parts. 

 

If you pass on this exerciser to another person or if you allow another person to use it, make sure  that 

that person is familiar with the content and instructions in these instructions. 

 

Only one person should use the exerciser at a time. 

 

Before the first use and regularly make sure that all screws, bolts and other joints are properly tightened 

and firmly seated. 

 

Before you start your work-out, remove all sharp-edged objects around the exerciser. 

 

Only use the exercise for your work-out if it works flawlessly. 

 

Any broken, worn or defective part must immediately be replaced and/or the exerciser must no longer 

be used until it has been properly maintained and repaired. 

 

Parents  and  other  supervisory  persons  should  be  aware  of  their  responsibility,  due  to  situations  which 

may arise for which the exerciser has not been designed and which may occur due to children’s natural 
play instinct and interest in experimenting. 

 

If you do allow children to use this exerciser, be sure to take into consideration and assess their mental 

and  physical  condition  and  development,  and  above  all  their  temperament.  Children  should  use  the 
exerciser only under adult supervision and be instructed on the correct and proper use of the exerciser. 
The exerciser is not a toy. 

 

Make sure there is sufficient free space around the exerciser when you set it up. 

 

To avoid possible accidents, do not allow children to approach the exerciser without supervision, since 

they  may  use  it  in  a  way  for  which  it  is  not  intended  due  to  their  natural  play  instinct  and  interest  in 
experimenting. 

 

Please note that an improper and excessive work-out may be harmful to your health. 

 

Please note that levers and other adjustment mechanisms are not projecting into the area of movement 

during the work-out. 

 

When setting up the exerciser, please make sure that the exerciser is standing in a stable way and that 

any possible unevenness of the floor is evened out. 

 

Always wear appropriate clothing and shoes which are suitable for your work-out on the exerciser. The 

clothes must be designed in a way so that they will not get caught in any part of the exerciser during the 
work-out due to their form (for example, length). Be sure to wear appropriate shoes which are suitable 
for the work-out, firmly support the feet and which are provided with a non-slip sole. 

 

Be sure to consult a physician before you start any exercise program. He may give you proper hints and 

advice with respect to the individual intensity of stress for you as well as to your work-out and sensible 
eating habits. 

IMPORTANT NOTES 

 

Assemble the exerciser as per assembly instructions and be sure to only use the structural parts provided 

with the exerciser and designed for it. Prior to the assembly, make sure the contents of the delivery is 
complete by referring to the parts list of the assembly and operating instructions. 

 

Be sure to set up the exerciser in a dry and even place and always protect it from humidity. If you wish 

to protect the place particularly against pressure points, contamination, etc., it is recommended to put a 
suitable, non-slip mat under the exerciser. 

Summary of Contents for UB60i




















Reviews: