background image

 

3.0  WARNINGS AND PRECAUTIONS 

 

Please read the following carefully before commencing work on this equipment. 
 
A competent  installation engineer, in accordance with the installation instructions of 
this  appliance  and  all  relevant  local  and  national  standards  including  the  following 
must install this appliance: 
 

  Health and Safety at Work Acts 

  IEE regulations 

  Local and National Building Regulations 

  BS Codes of practice 

  Water Supply Regulations   

 
Your new water boiler is designed to provide a constant source of near boiling water 
for the preparation of hot drinks. 

THIS IS VERY HOT

  

 
All  personnel  must  be  provided  with  sufficient  and  appropriate  training  in  the  safe 
use of this appliance. 
 
In line with Health & Safety requirements we recommend that a risk assessment be 
carried out after the boiler has been installed. 
 
A warning notice displayed next to the machine is often helpful in notifying users that 
the appliance contains and dispenses near-boiling water. 
 
During normal use of the boiler, certain surfaces will become hot (especially the draw 
off taps and swivelling dispense arms). Care should be taken to avoid potential injury 
from burns and scalding whilst operating the appliance. 
 
Scale formation within hot water appliances is problematic and more so in hard water 
areas. Damage to the appliance caused by excessive scale build-up may invalidate 
the warranty 

– see notes on de-scaling. 

 
Drawings, parts list, circuit/wiring diagrams are the sole property of Instanta Limited 
and must not be reproduced without their consent. 
 

 

This appliance is not intended for use by persons (Including Children) with reduced 
physical, sensory or mental capabilities, or lack of experience and knowledge, unless 
they have been given supervision or instruction concerning use of the appliance by a 
person responsible for their safety. Children should be supervised to ensure they do 
not play with the appliance 

 
 
 
 

Summary of Contents for MOD18











Reviews: