background image

LampLinc Owner’s Manual  

 

Page 14 of 14 

 

SPECIFICATIONS, CERTIFICATION, AND WARRANTY 

Specifications 

View specifications for LampLinc at: 

www.smarthome.com/2456D3.html

 

Certification 

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing 
laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the 
requirements of a widely recognized consensus of U.S. and Canadian device safety standards, that the 
manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-
up inspections to verify continued conformance.  

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of 
purchase, this product will be free from defects in material and workmanship and will perform in substantial 
conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or errors 
caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product does 
not perform as warranted above during the warranty period, Seller will either repair it, replace it, or refund the 
purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with proof of the date 
of purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for above 
shall be the full extent of Seller’s liability with respect to this product. For repair or replacement during the warranty 
period, call the INSTEON Gold Support Line at 800-762-7845 with the Model # and Revision # of the device to 
receive an RMA# and send the product, along with all other required materials to:  

Smarthome, Inc. 
ATTN: Receiving Dept.  
16542 Millikan Ave. 
Irvine, CA 92606-5027 

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, 
including any warranty or merchantability or fitness for a particular purpose. Any implied warranty, including any 
warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or supplanted as provided 
above shall be limited to the two-year of the express warranty above. No other representation or claim of any nature 
by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer.  
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical 
tampering. For optimal use, manually verify the device state. Any home automation device should be viewed as a 
convenience, but not as a sole method for controlling your home.  
In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or 
use of this device, including without limitation damage to property and, to the extent permitted by law, personal injury, 
even if Seller knew or should have known of the possibility of such damages. Some states do not allow limitations on 
how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case the above limitations 
and/or exclusions may not apply to you. You may also have other legal rights that may vary from state to state.  

INSTEON Technology Patent 

U.S Patent No. 7,345,998, International patents pending

  

© Copyright 2011 
Smarthome, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, 

www.smarthome.com

 

 

Rev 04-28-2011 

Summary of Contents for LampLinc 2456D3















Reviews: