background image

                                                          Page 14 of 15                                      2342-x32 Rev: 11/20/2012 4:13 PM 

 

Problem 

Possible Cause 

Solution 

One or more scene members is not 
responding and HouseLinc (or other 
software) is attempting to 
communicate to Mini Remote 

longer in use, or 

b)  Add INSTEON devices for better signaling 

Mini Remote is locked up 

Mini Remote may have glitched 

Power cycle Mini Remote by turning it off (slide 
power switch to left), waiting 10 seconds and 
turning it back on (slide power switch to right) 
 

Perform a factory reset on Mini Remote 

If you have tried these solutions, reviewed this Owner’s Manual, and still cannot resolve an issue, visit 

www.insteon.com/support

 for online support and updated product documents  

or call INSTEON Support Line at 866-243-8022 

 
 
 
 
 
 
 
 
 
 
 
 

Certification and Warranty 

Declaration of Conformity 

DECLARATION OF CONFORMITY  
Hereby, INSTEON declares that this device is in compliance with the essential requirements and other relevant provisions of the following Directives: 
1) Electromagnetic Compatibility Directive 2004/108/EC 
2) Hazardous Substance Directive 2005/95/EC 
Technical data and copies of the original Declaration of Conformity are available and can be obtained from INSTEON; 16542 Millikan Ave, Irvine, CA, 
USA. 
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) 
This  document  contains  important  information  for  users  with  regards  to  the  proper  disposal  and  recycling  of  INSTEON  products.  Consumers  are 
required to comply with this notice for all electronic products bearing the following symbol: 
Environmental Information for Customers in the European Union 
European  Directive  2002/96/EC  requires  that  the  equipment  bearing  this  symbol  on  the  product  and/or  its  packaging  must  not  be disposed  of  with 
unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.  
It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or 
local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.  
For  more  detailed  information  about  the  disposal  of  your  old  equipment,  please  contact  your  local  authorities,  waste  disposal  service,  or  the  shop 
where you purchased the product. 
DECLARATION OF CONFORMITY TO R&TTE DIRECTIVE 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein 
Product category: general consumer (category 3). 
 
English: This equipment is in compliance with the essential requirements and other relevant provisions of the European R&TTE Directive 1999/5/EC 
Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU. 
Nederlands [Dutch]: Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC. 
Svenska [Swedish]: Denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av 
direktiv 1999/5/EG. 
Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC 
Español [Spanish]: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE. 
Português [Portuguese]: Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC. 
Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE. 
Norsk [Norwegian]: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF. 
Suomi [Finnish]:Tämä laite tÿttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen. 
Dansk [Danish]: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF. 

Polski [Polish]: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami okreslonymi Dyrektywą UE: 1999/5/E

Summary of Contents for Mini Remote 2342-432































Reviews: