background image

These instructions describe the installation, assembly, operation, maintenance and fault finding of the Hiper Heat 
Interface Unit (HIU). For operation of the entire plant, the technical documentation of all the components used 
such as, boiler, tank, pumps, pipework and valves must be complied with. Inta does not accept any responsibility 
for the design and performance of the heat network or components outside of the HIU.

 

Installation should only be carried out by a qualified and competent plumbing installer and a qualified and 

 

competent electrical installer in accordance with the current Building, Water and Electrical Regulations, Legislation 
and Standards. Do not start installation until you have thoroughly read and understood these Assembly and Oper-
ating Instructions and have complied with all safety provisions.

 

 

Symbols used in this manual : 

 

DANGER 

 

immediate risk of physical injury or even death. 

 

DANGER 

 

immediate risk of serious damage.

   

 

IMPORTANT

 

 

information critical to the installation or installer.

 

IMPORTANT 

 

information critical to the user.

 

 

NOTE 

 

useful information regarding the operation or installation of the HIU.

 

SECTION 1 

-

 Important information  and introduction

 

Heat Interface Units 

(HIU

)

 deliver heat generated from a centralised heating plant to multiple homes, 

 

apartments or flats. 

The Inta Hiper V3 HIU interfaces the heat network and dwellings systems 

through a plate heat exchanger to 

provide hot water (DHWS) and with room heating (HTG) in a DIRECT 

connection to the heat network. 

 

 

HIUs do not generate their own heat so to deliver DHW and CH most suitable for the requirement of the 
home or apartment it is the responsibility of the installer and or system designer that the heat network 
delivers heat at 

 

sufficient flow rate and temperature to do so.

 

05/20 E&OE

 

Installation and Operating Instructions SECTIONS  

 

Page 2

 

1.

 

Important Information and Introduction

 

2.

 

Description

  

3.

 

Dimensions

 

4.  Technical Data

 

 

5.  Installation

   

6.  Operation of Unit

 

 

7.  Commissioning

 

 

8.  Fault Finding

  

9.  Servicing

 

10. Warranty

   

-

V3 DIRECT

 

Summary of Contents for HIPER-V3 DIRECT
















Reviews: