Inta Hiper Xi45 INDIRECT HIU 45DHW/10HTG Instructions Manual Download

Page: 12 / 28

SECTION 4

Installation and Assembly instructions

ACCESSORIES

HIAC08SSPACK

Description

Order as Part Code

Primary First Fix Kit

Price included with HIPER HIU

Can be delivered with HIU or in advance for first fix pipe
work.

(Use with HIPER First Fix Installation Kit

)

HIACPFFKIT

Stand off Wall Brackets

To allow pipes from above or below to run
behind the HIU.

HIAC01S0BPACK

Secondary Side Isolation Valves.

WRAs approved ball valves with union ¾

”

nuts to fit directly to the HIU secondary con-
nections. Wras approved

HIAC03BVPACK

Prepayment 230v Relay Kit

(for pre

payment billing network with 230v

signal)

HIAC04230KIT

Security Fixing Screws with special drive bit
for locking and removal.

Prevents casual tampering

HIAC05SSPACK

First Fix Jig

Reusable jig for installing the isolation valves,

before installing the HIU .

HIAC06SSPACK

HIU Panel Insulation Set

Insulation set for the back of the HIPER HIU

HIAC07SSPACK

Link Pipe Accessory Pack

for flushing the pri-

mary pipework without the HIU installed.

HIAC08SSPACK

HIU Accessory Pack HIU Isolation Valves

22mm x ¾

”

union nut

ANGLE

Female Ball

Valves (4) alternate secondary side

connections

HIAC09BVPACK

HIU Accessory Pack HIU Isolation Valves

”

male x ¾

”

union nut

ANGLE

Female Ball

Valves (4) alternate secondary side connec-
tions

HIAC10BVPACK

Intaklean Compact Magnetic Filter/Strainer

protecting the heating system and HIU PHE

IKCMF34

Weather Compensation Sensor and Box

RB8410000

Zenner

Heat Meter

Mid Class 2

ZE102C5

ActivFlo Water Conditioner

Prevents scale formation through the entire
DHW circuit, protecting the HIU, taps,

showers etc. in hard water areas

Please ask for

further details

www.activ

tec.com

Ph. 01889 272197

Pack 1

STAND OFF

wall Brackets

Pack 3 secondary side ball valves

Primary First Fix Kit

First Fix JIG

ANGLE isolation ballvalves

Stage

09/17 E & OE

Summary of Contents for Hiper Xi45 INDIRECT HIU 45DHW/10HTG





























Search results

Summary of Contents for Hiper Xi45 INDIRECT HIU 45DHW/10HTG

Reviews:

Related manuals for Hiper Xi45 INDIRECT HIU 45DHW/10HTG

Brands by name

Popular brands

Inta Hiper Xi45 INDIRECT HIU 45DHW/10HTG, Instructions Manual

Search results

Summary of Contents for Hiper Xi45 INDIRECT HIU 45DHW/10HTG

Reviews:

Related manuals for Hiper Xi45 INDIRECT HIU 45DHW/10HTG

Brands by name

Popular brands