Intec Controls MSR ELECTRONIC PolyGard AT-1110 User Manual Download

Page: 13 / 17

Customer Services (858) 578-7887 & (888) GO IN

TEC

Controls, 12700 Stowe Dr., Suite 1

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 141114

Polygard® is a registered trademark of MSR

AT-1110V3

PolyGard

CO Transmitter

User Manual - AT-1110 V3

Page 13











NEMA3(IP45)

w/probe

7/8in.(22mm)diameterand

7.16in.(182mm)length

Cableentry

1holefor1/2in.conduit



NEMA4X(IP65),w/splashguard

Material

ABSUL94V0

Color

Lightgray

Dimensions(HxWxD)



4.80x4.72x3.42in.

(122x120x87mm)



NEMA12(IP55)

Material

Polycarbonate,UL94HB,fireretardant

Color



Lightgray

Dimensions(HxWxD)

5.12x3.31x2.95in.

(130x84x75mm)

Conformity



UL50standards

Cableentry

1holesfor1/2in.conduitforwall(surface)

mountedand1holeonbacksideofbaseplate

forsinglegangelectricalboxmounting

connectionTerminalblocks.



Specifications subject to change without notice. | USA 141114 | Page 13 of 17

Polygard® is a registered trademark of MSR | AT-1110V3

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110_V3 – UserManual

Specifications subject to change without notice. | USA 160104 | Page 13 of 17

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110 V3 – UserManual

PolyGard

is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110


















Search results

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110

Reviews:

Related manuals for MSR ELECTRONIC PolyGard AT-1110

Brands by name

Popular brands

Intec Controls MSR ELECTRONIC PolyGard AT-1110, User Manual

Search results

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110

Reviews:

Related manuals for MSR ELECTRONIC PolyGard AT-1110

Brands by name

Popular brands