background image

W0008-1

E

SN 29343005

Integra Division of
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramsey, N.J. 07446, U.S.A.
Tel: 201-825-7950  Fax: 201-825-8150  E-mail: integra@onkyousa.com

Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div. : 
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111  Fax: 072-833-5222

Specifications

AMPLIFIER SECTION

Power Output:

100 Watts per channel min. RMS at
8 ohms, both channel driven from
20 to 20,000 Hz with no more than
0.08 % total harmonic distortion.

125 Watts per channel min. RMS at
6 ohms, both channel driven from
1 kHz with no more than 0.1 %
total harmonic distortion.

Dynamic Power Output:

×

 140 Watts at 8 ohms

Total Harmonic Distortion:

0.08 % at rated power

IM Distortion:

0.08 % at rated power

Damping Factor:

100 at 8 ohms

Input Sensitivity and Impedance: 1 V, 50 kohms

Output Level and Impedance:

1 V, 10 kohms

Rated Speaker Impedance:

6 ohms MIN

Frequency Response:

10 Hz – 100 kHz, ±1 dB

Signal-to-Noise Ratio:

110 dB (IHF A, 0.5 V input)

GENERAL

Power Supply:

AC 120 V, 60 Hz

Power Consumption:

2.5 A

Dimensions (W 

×

 H 

×

 D):

435 

×

 145 

×

 316 mm

17-

1

/

8

×

 5-

11

/

16

×

 12-

7

/

16

"

Weight:

8.5 kg, 18.7 lbs.

Specifications and features are subject to change without notice.

#US_ADM-2.1_08.p65

8/25/00, 6:22 PM

8

Summary of Contents for ADM-2.1









Reviews: