background image

 

USER MANUAL 

 OPTIMA-33 10K/20K/30K 

www.xmart-ups.com                                                                       

170502-OPTIMA-33 10K/20K/30K (ENGLISH) - 41 

 

 

    14.- LIMITED WARRANTY   

 

 

 

 

 

 

 

 

 

 

                   

       

 

Support: 

If a failure or problem is detected please check troubleshooting section in user manual. If problem cannot be solved please contact 

authorized service center or authorized dealer. 
 

Batteries:

 Rechargeable batteries can be charged and discharged hundreds of times. However they will eventually wear out. This is not a defect 

or failure so that batteries wear out is not covered by this warranty. 
Battery lifetime will depend of operative conditions like working temperature, type and frequency of discharging cycles. Higher the temperature 
shorter will be the lifetime. Frequent and deep discharging cycles also will short lifetime. For critical applications batteries should be revised and 
replaced periodically. Long storage (longer than 6 months) without required recharging will wear out batteries. This situation is not covered by 
this limited warranty since this is not considered as a defect. Check recharging instructions on user manual. 
 

Conditions - Limited Warranty 

1.- Subject to the conditions of this limited warranty, this product is warranted to be free from defects in materials and workmanship at the time 
of XMART supplies the product. 

 

In Europe, warranty time is 1 year on electronic parts and 1 year on internal batteries from XMART invoice date. 

 

In America, standard warranty times could vary depending on country/region or can be extended by purchasing warranty options. Please 

check warranty plans and extensions with your local distributor.   

2.-  If  during  the  warranty  period,  this  product  fails  to  operate  under  normal  use  and  service,  due  to  defects  in  materials  or  workmanship, 
authorized  distributor  or  service  center  will,  at  their  option,  either  repair  or  replace  the  product  in  accordance  with  terms  and  conditions 
stipulated herein. Transportation expenses are not covered by this limited warranty. 
3.- Warranty is valid only if the original purchasing document, specifying date of purchase, serial number and name of the dealer, is presented 
with the product to be revised. XMART and authorized partners reserve the right to refuse warranty service if any of this information has been 
removed, changed or missing in original invoice document. 
4.- If product is repaired or replaced, repaired or replaced product will be warranted for the remaining time of the original warranty or for 90 
days on repaired part from date of repair, whichever is longer. 
5.-  XMART  or  their  distribution/service  partners  reserve  the  right  to  charge  handling  fee  if  returned  product  is  free  of  failure  or  it  is  out  of 
warranty because any of the reasons described in this warranty.   
6.- If product is out of warranty a reparation proposal will be sent to the user for his approval. If proposal is not accepted, service center will 
keep product available for the user during 60 continuous days. After this period product would be disposed and user will not be able to rise any 
claim.   
7.- Rechargeable batteries, like included in this product, will definitively wear out even under normal operation. This is not a defect or failure so it 
is not covered by this warranty.   
8.-  This  warranty  does  not  cover  batteries  wear  out  caused  by  improper  or  long  storage  (over  6  months  without  required  recharging  as 
indicated  in  product  manual).  Even  performing  recharging  procedure  this  product  cannot  be  storage  longer  than  18  months.  Problems  on 
batteries caused by this kind of long storage are not covered by this warranty. 
9.- This warranty does not cover product failures caused by installations, modifications or repair performed by non-authorized person. If product 
is open by not authorized technician warranty will be considered void. This warranty does not cover failure caused by inadequate installation or 
maintenance, misuse, accidents, fire or floods. 
10.- This product can include protection devices like input fuse or input breaker. Activation of this kind of devices is not a failure it is caused by 
an improper product installation. Input fuse or breaker reset or replacement is not covered by this warranty.   
11.- This warranty does not cover damages produced during transportation from user to technical service caused by improper packing of the 
product by user. 
12.- Warranty terms and conditions cannot be modified or extended by third parties without written approval of XMART. 

 
Limited Warranty 

- XMART does not warrant that the operation of this product will be uninterrupted or error-free during its lifetime. If product fails to work, the 
maximum liability of XMART under this limited warranty is expressly limited to the lesser of the price you have paid for the product or the cost of 
repairing or replacement of any hardware components that malfunction in conditions of normal use. 
- In no event will XMART be liable for any damages caused by the product or the failure of the product to perform, including any lost profits or 
savings or special, incidental, or consequential damages. XMART is not liable for any claim made by a third party to XMART or to final user.   
- XMART is not responsible for damage that occurs as a result of your failure to follow the instructions intended for this hardware product. 

 
 
 
 
 
 

Summary of Contents for Xmart OPTIMA-33 10K













































Reviews: