background image

 

 

 Glassgate 150 Maintenance 

 

© Integrated Design Ltd 

Issue A1 August 2012 

  Page 15 of 15 

 

Warranty 

 
Integrated  Design  Ltd.  (The  Company)  warrants  that  products  manufactured  by  it  are  of 
merchantable  quality,  free  of  any  rightful  claim  of  infringement  or  the  like. When  used  in  the 
manner intended, will be free of defects in materials or workmanship for a period of twelve (12) 
months from the date of sale as shown by a sales invoice or warranty registration card on file 
with the Company. The terms of warranty are as per Integrated Design Ltd. Conditions of Sale 
and will not apply to any product which has been modified, or improperly used or repaired after 
leaving  the  Company's  control.    Any  implied  warranty  of  fitness  for  particular  purposes, 
whether  express  or  implied,  is  hereby  expressly  excluded. These  warranty  terms  may  not  be 
modified except in writing approved and issued by an authorised officer of the Company. 
 
 

Technical Support 

 
We welcome inquiries and comments regarding all of our products.  We trust you will find them 
easy  to  install  and  reliable  in  operation.  Should  you  experience  any  application-related 
difficulties however, in the first instance please contact your supplier.  
 
Our direct contact details are: 
 

Fax: 

UK 

0208 890 2444 

 

International 

+44 208 890 2444 

Web: 

www.fastlane-turnstiles.com 

Email:  support@idl.co.uk 

Tel: 

UK 

0208 844 8536 

 

International 

+44 208 844 8536 

 
A  technical  support  form  may  be  downloaded  from  the  web  site,  please  use  this  form  to 
provide  a  description  of  the  reported  fault  and  the  corrective  action  diagnostics  information 
already attempted. 
 
If a sub-assembly is to be returned for warranty or non-warranty testing, please use the Return 
to  Manufacturer  Authorisation  system  (RMA).  Information  about  this  is  available  on  the  web 
site. 
 
 

Important Notice 

 
Although every effort has been made to make this manual as accurate as possible, IDL does 
NOT accept any liability for errors or omissions. The data contained in this manual supersedes 
any  other  information  published  on  the  Product.  We  further  reserve  the  right  to  amend  or 
improve the equipment and/or manual without notice. 

 

 

 

 

Version History 

Issue 

Date 

Change 

Ref 

A0 

03/08/12 

Initial Release 

A1 

31/08/12 

Added Optical card replacement, improved enclosure details 

CN2075 

 

 

 

 

 

 

 

 

Summary of Contents for Fastlane Glassgate 150
















Reviews: