background image

Adapter Hardware

True Scale Fabric Adapter Hardware

Installation Guide

July 2015

12

Order Number: G91929004US

Note:

If you want to use the QLE7340 or QLE7342 in QDR mode, a QDR-capable InfiniBand

*

 

switch must be used.

For cabling instructions, see 

“Cabling the Adapter to the Switch” on page 17

.

3.2

Safety with Electricity

Observe these guidelines and safety precautions when working around computer 

hardware and electrical equipment:

• Locate the power source shutoff for the computer room or lab where you are 

working. This is where you will turn OFF the power in the event of an emergency or 

accident. Never assume that power has been disconnected for a circuit; always 

check first. 

• Do not wear loose clothing. Fasten your tie or scarf, remove jewelry, and roll up 

your sleeves. Wear safety glasses when working under any conditions that might 

be hazardous to your eyes. 

• Shut down and disconnect the system’s power supply from AC service before you 

begin work, to insure that standby power is not active. Power off all attached 

devices such as monitors, printers, and external components. Note that many 

motherboards and power supplies maintain standby power at all times. Inserting or 

removing components while standby is active can damage them.

• Use normal precautions to prevent electrostatic discharge, which can damage 

integrated circuits.

3.3

Unpacking Information

This section provides instructions for safely unpacking and handling the Intel

®

 adapter. 

To avoid damaging the adapter, always take normal precautions to avoid electrostatic 

discharge.

3.3.1

Verify the Package Contents

The Intel

®

 adapter system should arrive in good condition. Before unpacking, check for 

any obvious damage to the packaging. If you find any obvious damage to the 

packaging or to the contents, please notify your reseller immediately.

3.3.2

List of the Package Contents

The package contents for the QLE7340 adapter are:

• Intel

®

 QLE7340

• Additional short bracket
• Readme First

Standard PCIe risers can be used, typically supplied by your system or motherboard 

vendor.

The package contents for the QLE7342 adapter are:

• Intel

®

 QLE7342

• Additional short bracket
• Additional standard bracket
• Readme First

Summary of Contents for QLE7340



















Reviews: