background image

IntelliSAW IRM-48 Reader 

 

Installation Manual 

 

Page 14 of 28 

IRM-48 Reader 

 

910.00371.0001 

 

4

 

W

IRING

 

 

   WARNING 

SYSTEM WIRING SHOULD BE PERFORMED ONLY BY PERSONNEL WHO ARE 
TECHNICALLY COMPETENT AND AUTHORIZED TO DO SO. LOCAL REGULATIONS 
REGARDING ELECTRICAL INSTALLATION AND SAFETY MUST BE OBSERVED. 

Failure to follow the instructions given can result in death or serious injury 

 

   WARNING 

TO AVOID ELECTRICAL SHOCK. AC POWER WIRING MUST NOT BE CONNECTED TO 
THE SOURCE UNTIL ALL WIRING CONNECTIONS PROCEDURES ARE COMPLETED. 
 

Failure to follow the instructions given can result in death or serious injury 

 

   WARNING 

CHECK THE INFORMATION LABEL ON THE CASE TO DETERMINE THE CORRECT 
VOLTAGE BEFORE CONNECTING TO A LIVE SUPPLY. 
 

Failure to follow the instructions given can result in death or serious injury 

 

 

IMPORTANT 

The wiring diagram below shows all possible combinations. The actual connections required 
depend upon your system installation. 

 

 

The Reader terminal connections are illustrated in the figure below. In general, all wiring 
connections are made to the instrument after it is installed.   

 

 

Summary of Contents for IRM-48





























Reviews: