background image

 

 

1

 

 

 

! Warning

 

Cautious & Attention 

 

Warning: 

It represents conditions or

 

 actions which can possibly cause 

people to be injured or dead. 

 

Cautious:   

It represents conditions or

 

actions which can possibly cause 

monocular damaged or data loss.  

 

Attention:  

It represents valuable notes for users.  

Important information - 

Please read user’s manual before you 

use it.  

 

Never put the lens directly towards to the strong radiation source (the 
Sun, direct or reflection lasor beam, etc ) in any situation (power on or 
power  off)  since  thermal  inductor  used  in  infrared  telescope  is  very 
sensitive. Otherwise, infrared telescope will be damaged permanently.  

 

The original package box must be used in the transportation. Do not 
shake or hit the apparatus strongly in use and transportation. 

 

Please  use  the  original  package  box  to  store  the  apparatus.  The 
environment  should  be  cool,  dry,  ventilated  and  no  strong 
electromagnetic field. 

 

Protect the surface of the lens from being stained or damaged by oil 
sludge  and  any  chemical  matters.  Please  put  on  the  lens  cap  after 
using.  

 

Please remember to backup the data into PC instantly in order to avoid 
losing the important data.  

 

Never  open  the  case  or  refit  the  apparatus.  Only  authorized  people 
from our company are allowed to do maintenance.  

Summary of Contents for ThermalTronix TT-1230S Series





















Reviews: