background image

Battery installation should be performed by an adult. Use only batteries recommended in the instruction manual. 

Be careful to install the batteries in the correct polarity as indicated.

-Do not mix old and new batteries

-Do not mix Alkaline, standard and/or rechargeable batteries

-Rechargeable batteries are to be charged under adult supervision

-Depleted batteries are to be removed from the toy

-The Supply terminals are not to be short-circuited

CAUTION: Snowmobile contains rechargeable cells. If fluid leaks from the snowmobile avoid contact with eyes and 

dispose of snowmobile.

IMPORTANT BATTERY INFORMATION

REQUIRED BATTERIES:  RC Snowmobile uses a 9.6V rechargeable battery pack.  

Controller/Charger requires one (1) 9  Volt Alkaline battery.

1. The Polaris RUSH RC Snowmobile is factory assembled, ensure that the correct skis are installed on the snowmobile for  

    the surface you intend to run on.

2. Insert the antenna into the transmitter and screw into place finger tight. 

3. Left /Right steering trim is located on the bottom of the snowmobile and can be easily adjusted by moving the trim arm. 

    The snowmobile should be able to drive a straight line, if it always turns right then move the trim arm to the left, if it always 

    turns left move the trim arm to the right.

BASIC ASSEMBLY

TIP:

 When the using the snowmobile for the first time or after leaving the snowmobile sit for a long period of time the 

battery might not be in its peak condition. Best performance will return after re-conditioning the snowmobile’s batteries, 

this is a accomplished during normal use. To do this simply charge the snowmobile completely and then discharge the 

battery completely by running the motor while holding onto the snowmobile, after the motor stops running re-charge the 

snowmobile and have fun!  

Note: The battery must be fully charged before using your snowmobile for the first time. 

CHARGING YOUR SNOWMOBILE

1. Remove the battery from the 

snowmobile. Note: Always remove the 

battery from the snowmobile during 

charging as this keeps the battery cooler. 

Never leave the battery unattended 

while charging.

2. Plug the battery into the charger 

as shown. A typical charge takes 4 

hours to complete. After charging 

unplug the battery from the charger 

and unplug the charger from the wall.

3. Plug the charger adaptor into the 

AC wall outlet.

Never allow the battery pack to become hot during charging – this will cause permanent damage. Warm is okay – hot is not!

Never leave the battery pack unattended while it is being charged.

Never recharge a warm or hot battery. Always allow the battery to cool to ambient temperature.

Do not attempt to over charge the battery by allowing it to charge for too long or performing more than one charge before using the battery.

Rechargeable batteries are to be removed from the toy before being charged.

IMPORTANT BATTERY INFORMATION

OPERATING INSTRUCTIONS

1) Fully extend the 

controller antenna.

2) Turn the controller ON.

3) Install the battery in the snowmobile.

•Open the battery compartment by removing the cover.

•Connect the battery (as shown).

•Insert the battery into the compartment (as shown).

Operation:

Forward /Backward Control

 -Move the throttle control away from you to make the 

snowmobile move forward. -Move the throttle control toward you to move backward

NOTE: The more you move the control the faster the snowmobile will move.

4) Turn the snowmobile ON 

– the head lights will turn on.

Operation:

Steering Left & Right -

To turn left move the directional 

control stick to the left.

-To turn right move the directional control stick to the right.

NOTE: The snowmobile will only turn when it is moving 

forwards or backwards.

Operation:

Control Reversal -

When the snowmobile is moving towards 

you the controls react as if they are reversed. For example 

to make the snowmobile move left requires you to steer right

 – just imagine that you are in the driver’s seat!

1) Remove the snow ski by unscrewing the 

    mounting screw using a Philips screwdriver, 

    be sure to keep the mounting screw.

2) Store the removed skis and install the 

    optional “Rug Runner” skis. The ones

    with wheels.

3) Replace screw and tighten securely.

CHANGING BETWEEN SKIS

ONLY USE THE CHARGER PROVIDED WITH THE INTERACTIVE TOY CONCEPTS POLARIS RUSH 

SNOWMOBILE, DO NOT USE ANY OTHER SOURCE TO CHARGE THE SNOWMOBILE’S BATTERIES

Reviews: