background image

15

o

 Coil Nailer

Drives Wire Collated Nails (2" to 3-1/4")

Model No. CN80-15, Item No. 65565

Model No. CN80F-15, Item No. 65566

6

Interchange Brands  

Operator’s Manual

!

safety Information

Important Safety Instructions for 

Operating Nailers

READ ALL INSTRUCTIONS

1 . 

OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY 

GLASSES WITH SIDE SHIELDS.

Danger to the eyes exists due to the possibility of flying fasteners 

and debris when operating the nailer . To guard against these 

hazards always wear safety glasses with side shields to protect both 

the front and sides . Make sure others in the work area wear safety 

glasses, too .
Eye protection equipment must conform to the requirements of 

American National Standards Institute, ANSI Z87 .1 .

The employer is responsible to enforce the use of eye protection equipment by the tool 

operator and other personnel in the work area .

2 . 

EAR AND HEAD PROTECTION MAY BE NEEDED IN SOME 

ENVIRONMENTS. 

Some work areas may include exposure to high noise levels which 

can lead to hearing damage . Always wear ear protection to protect 

your ears from loud noise . Wear head protection to protect your 

head from flying objects .

3 . 

KEEP FACE, HANDS AND FEET AWAY FROM FIRING HEAD 

AT ALL TIMES. 

Never place your face, hands or feet near the firing head .

4 . 

KEEP FINGER AWAY FROM TRIGGER WHEN NOT DRIVING FASTENERS 

TO AVOID ACCIDENTAL FIRING.
Always carry the nailer by the handle only . Never carry the nailer with your finger 

on trigger since you could drive a fastener unintentionally and injure yourself or 

someone else .

5 . 

NEVER POINT NAILER AT YOURSELF OR OTHERS IN WORK AREA.
Respect the nailer as a working implement . Always assume the nailer contains 

fasteners and never point the nailer at yourself or others, whether or not it 

contains fasteners . If fasteners are mistakenly driven, it can lead to severe 

injuries . Never engage in horseplay with the nailer . 

6 . 

DRESS PROPERLY. 

Do not wear loose clothing or jewelry as they can be caught in moving parts . 

Rubber gloves and nonskid footwear are recommended when working outdoors . 

Wear protective hair covering to contain long hair .

7 . 

KEEP VISITORS AWAY. 

All visitors should be kept safely away from work area and should not handle the 

nailer .

8 . 

KEEP OUT OF REACH OF CHILDREN.

9 . 

DO NOT OVERREACH. 

Keep proper footing and balance at all times .

Summary of Contents for 65565

























Reviews: