background image

Warranties and Liabilities

The information and the software discussed in this document are subject to change without notice and should not
be considered commitments by Intergraph Corporation.  Intergraph Corporation assumes no responsibility for any
errors in this document.

The software discussed in this document is furnished under a license and may be used or copied only in accordance
with the terms of the license.  No responsibility is assumed by Intergraph for the use or reliability of software on
equipment that is not supplied by Intergraph or its affiliated companies.

All warranties given by Intergraph Corporation about equipment or software are set forth in your purchase
contract, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a
modification or amendment of such warranties.

Copyright

 1997, Intergraph Corporation including this documentation, and any software and its file formats and audio-

visual displays described herein; all rights reserved; may only be used pursuant to the applicable software license
agreement; contains confidential and proprietary information of Intergraph and/or other third parties which is
protected by copyright, trade secret and trademark law and may not be provided or otherwise made available
without prior written authorization.

Restricted Rights Legend

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision
(c)(1)(ii) of the rights in technical data and computer software clause at DFARS 252.227-7013.

Unpublished rights reserved under the copyright laws of the United States.

Intergraph Corporation

Huntsville AL 35894-0001

Trademarks

Intergraph

 and the Intergraph logo are registered trademarks of Intergraph Corporation.  ErgoAct is a trademark

of Intergraph Corporation.  Other brands and product names are trademarks of their respective owners.

Summary of Contents for ErgoAct OEM Monitor



















Reviews: