background image

FCC Certification

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: (1) This device may not cause harmful 

interference, and (2) This device must accept any interference received, including interference 

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a CLASS B digital 

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a residential 

installation. This equipment generates, uses, can radiate radio frequency energy and if not 

installed and used in accordance with the instruction guide, may cause harmful interference to 

radio communications. However, there is no guarantee that this radio interference will not occur 

in a particular installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment on and off, the user is encouraged 

to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Consult the dealer or an experienced Radio-TV technician for help. 

Notice: Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. Extension cables are not 

recommended, if used, they must be shielded in order to comply with the emission limits.

IC Certification

The term “IC” before the certification/registration number only signifies that the Industry Canada 

technical specifications were met. 

Declaration of conformity

Manufacturer:  

SMK-Link Electronics Corporation 

 

 

3601-B Calle Tecate

 

 

Camarillo, CA 93012 

Hereby, SMK-Link. declares that the VP4910 is in compliance with the essential requirements 

and other relevant provisions of Directive 1999/5/EC. 

EMC/EMI/Safety Standards: 

EN 300 440-2 V1.1.1 (2001-09)

EN 301 489-1 V1.4.1 (2002-08)

EN 301 489-3 V1.4.1 (2002-08)

EN 60825-1 (1994, A11:1996, A2:2001)

Summary of Contents for Jade VP4910













Reviews: