background image

 

 

Copyright 

 

© 2013    UTC Fire & Security Americas Corporation, Inc.   

Interlogix is part of UTC Climate Controls & Security, a unit of United 
Technologies Corporation.   All rights reserved. 

Trademarks and patents 

 

The IFS NS2503-8P/2C and logo are trademarks of United 
Technologies. 

Other trade names used in this document may be trademarks or 
registered trademarks of the manufacturers or vendors of the respective 
products. 

Intended use 

 

Use this product only for the purpose it was designed for; refer to the 
data sheet and user documentation for details. For the latest product 
information, contact your local supplier or visit us online at 
www.interlogix.com. 

Manufacturer 

 

UTC Fire & Security Americas Corporation, Inc.   
2955 Red Hill Avenue 
Costa Mesa, CA 92626-5923, USA   
EU authorized manufacturing representative: 
UTC Fire & Security B.V., Kelvinstraat 7,   
6003 DH Weert, The Netherlands 

Certification 

 

 

 

N4131 

FCC compliance 

 

This equipment has been tested and found to comply with the limits for a 
Class A digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio 
communications. 
You are cautioned that any changes or modifications not expressly 
approved by the party responsible for compliance could void the user's 
authority to operate the equipment. 

ACMA compliance 

 Notice!

 This is a Class A product. In a domestic environment this 

product may cause radio interference in which case the user may be 
required to take adequate measures. 

Canada 

 

This Class A digital apparatus complies with Canadian ICES-003. 
Cet appareil numérique de la classe A est conforme á la norme 
NMB-003du Canada.

 

European Union directives   

2004/108/EC (EMC Directive): 

Hereby,

 UTC Fire & Security Americas 

Corporation, Inc.

 declares that this device is in compliance with the 

essential requirements and other relevant provisions of Directive 
2004/108/EC.

 

 

 

 

 

2002/96/EC (WEEE directive): 

Products marked with this symbol 

cannot be disposed of as unsorted municipal waste in the European 
Union. For proper recycling, return this product to your local supplier 
upon the purchase of equivalent new equipment, or dispose of it at 
designated collection points. For more information see: 
www.recyclethis.info.

 

Contact information 

 

For contact information see our Web site: 

www.interlogix.com

Contact support 

 

www.interlogix.com/customer support

 

 

Summary of Contents for IFS NS2503-8P/2C












Reviews: