NX-148E- RF LCD Touchpad w ith Receiver Installation Instructions
3
RM
: receiver module
HE
: hardwire expander
P
: panel
This gives you all the programming information in one place
and facilitates the programming process.
Zone locations 401 to 592
Zone locations 401 to 592 are not numbered in
Table 11
since
these locations vary depending on location 594, Receiver Zone
Bank Setting.
For example, if location 594 is set to 3, the first available
location is 425. The total number of available locations is
dependant on the zone limits for both the panel and receiver.
The default settings shown for Segments 1 and 2 in the first
zone location apply to all zone locations.
Set touchpad number and partition (94)
To set the touchpad number and partition, do the following:
1. Enter * 94.
2. Enter your program code.
3. Enter the touchpad number (see
Table 2
) and press *.
4. Enter the partition number and press *.
5. To exit, press #.
Table 2. Device num bers
Partition
Touchpa
d
1
2
3
4
5
6
7
8
1
192
193
194
195
196
197
198
199
2
200
201
202
203
204
205
206
207
3
208
209
210
211
212
212
214
215
4
216
217
218
219
220
221
222
223
5
224
225
226
227
228
229
230
231
6
232
233
234
235
236
237
238
239
7
240
241
242
243
244
245
246
247
8
248
249
250
251
252
253
254
255
Add transmitters
To add transmitters to the touchpad receiver, do the following:
1. Enter * 8 at the touchpad.
2. Enter your program code (factory default is 9 7 1 3).
3.
Enter the devic e numbe r (
Table 2
) and pres s #.
4.
To load factory default s and clear unwant ed informat ion in
memory for new installat ions , enter 9 1 0 #.
5. To determine the starting zone number for the specific
touchpad receiver on new installations, set the receiver
zone bank (Location 594) The bank setting is based on
the zone capabilities of both the receiver and the panel
and must be set before you add (learn) transmitters.
6.
Enter 400 # to enter the sens or (trans m itt er) learnin g
location.
7. Enter a zone number (1 to 192) and press *. Three beeps
from the touchpad indicates an entry error. This occurs if
you enter a transmitter number that is not within the
receiver’s zone block or if you try to learn a transmitter that
is already learned into the receiver.
Note
: If you change your mind about your entry, enter
400
# 0*
to terminate programming and start over from step 6.
8.
Trip the desired trans mitt er (within 250 second s) as
desc rib ed in
Table 3
. Listen for the
ding dong
for
confirm at ion
Table 3. Tripping transmitters
Transmitter
Action
Door/w indow , shock, glass
guard, freeze, UFT
Activate tamper sw itch by removing
cover.
Door/w indow with external
contact
Activate tamper sw itch by removing
cover.
Feature 4
—Input option 1, must be on.
Recessed door/w indow
Activate tamper sw itch by removing
circuit board until tamper sw itch is
exposed.
Micro door/w indow and
Micro recessed door/w indow
Refer to the installation instructions for
the specific sensor for activation
information.
SlimLine door/w indow
Remove cover, then press the button
on the top of the sensor, or activate
the tamper sw itch by removing the
cover.
PIR
Refer to the installation instructions for
the specific sensor for activation
information.
Smoke detector w ithout
tamper sw itch
Press and hold the test button.
Smoke detector w ith tamper
sw itch
Trip the tamper sw itch. Feature 4
—
Input option 1, must be on.
Heat detector
Press, then release the tamper sw itch.
Single button panic
Press and hold the button.
Dual button panic
Press and hold both buttons together.
Keyfobs
Press and hold the arm and disarm
buttons together.
Repeater
Press, then release the tamper sw itch.
