SETTING / OPERATING INSTRUCTIONS
Indicator LED “ON”
when connected to
power source and con-
tacts are closed
Display
Reset port
to cancel all
prior settings
ON/AUTO/OFF
Select Key
Function Keys
.
NOTE: Timer will resume automatic operation with
the next opposite setpoint.
To Override Automatic Operation Permanently:
Press SELECT key to move indicator bar to the desired
ON or OFF position. Note: Timer will not resume
automatic operation until indicator bar is
repositioned above the word AUTO.
Because of our commitment to continuing research and improvements, Intermatic Incorporated reserves the right to make changes, without notice, in the specifications and material
contained herein and shall not be responsible for any damages, direct or consequential, caused by reliance on the material presented.
INTERMATIC INCORPORATED,
SPRING GROVE, IL 60081-9698
http://www.intermatic.com
158PB12524
ONE YEAR LIMITED WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its
sole option, the unit free of charge. This warranty applies only to the original purchaser and is not transferable. This warranty does not apply to: (a) damage
caused by accident, abuse, mishandling, dropping, acts of God, or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken
apart, or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product. Some states do not allow a
limitation of damages, so the foregoing limitation may not apply to you. This warranty gives you specific legal rights and you may have other rights that vary
from state to state.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR
IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY
PERIOD STATED ABOVE.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing postage prepaid to the
nearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by:
Intermatic Incorporated/After Sales Service, 7777 Winn Rd., Spring Grove, IL 60081-9698/815-675-7000 http://www/intermatic.com
Symptom
Possible Cause(s)
Corrective Action
Blank Display
Discharged battery ................................Replace battery
Defective timer .....................................Replace timer
Timer will not respond
Memory is full ......................................Press to clear memory
to programming
Timer will not function
Timer is in the wrong ..........................Press SELECT key and move
as programmed
SELECT mode
indicator bar over to AUTO
Timer is ON at all times
Timer is in ON mode ............................See above
Defective timer .....................................Replace timer
TROUBLESHOOTING
Programming Instructions
To Set or Change the Time of Day: To clear entire
memory, press key. Hold down the CLOCK key
while pressing either the HOUR or MINUTE keys.
Continue pressing until the desired number is shown.
Then simply lift finger off the CLOCK key to set.
To Set Program (ON/OFF times): Press TIMER key
once to enter into program mode. Display will show
“1 ON-- --”. Press the HOUR key and then the
MINUTE key to select the desired first ON time. Press
TIMER key once. Display will show “1 OFF -- --”.
Repeat previous step to select the desired first OFF
time. Repeat the entire sequence to complete up to
eight total ON/OFF times as desired. When program-
ming is done, press the CLOCK key then the SELECT
key repeatedly until the indicator bar is above the word
“AUTO”.
To Review Program: Press TIMER key repeatedly.
When done, press CLOCK key to return to the time
of day.
To Cancel/Change Part of the Program: Press
TIMER key repeatedly until the particular ON or OFF
time appears. Set new ON of OFF time. (See: To Set
Programs).
To Override the Automatic Operation one time:
Press OVR. KEY.
To Cancel/Change Part of the Program: Press
TIMER key repeatedly until the particular ON or OFF
time appears. Set new ON or OFF time. (See: To set
Programs).
To Override the Automatic Operation one time:
Press OVR. KEY.
