DCS 300 User’s Manual
8-16
Your applications will use TCP sockets to communicate with the DCS 300 across a
TCP/IP network. The DCS 300 sets up two channels:
Receive channel
The low priority Receive channel handles unsolicited transactions
from devices and applications, and handles system transactions from applications.
ACK channel
The high priority ACK channel handles acknowledgment (ACK)
transactions from applications and devices.
The DCS 300 creates one auxiliary channel (
AUX_Q
) for each known application.
Transactions that are held in
AUX_Q
have not been saved on disk. If you have a lot of
unprotected power failures, you can reduce the risk of data loss by using the local
interface to set the Transactions held in volatile memory parameter, as follows:
•
If you set the parameter to a small number, only that many transactions can be lost
during a power failure.
•
If you set the parameter to 0, no transactions are held in volatile memory. Instead,
all transactions that would have been written to
AUX_Q
are instead written to a Hot
Standby file.
When you configure the DCS 300, you must pick a realistic value for the Hot Standby
timeout so that the DCS 300 does not hold too many transactions in the auxiliary
channels. Once an application goes into Hot Standby mode, performance and
throughput decrease because the transactions for the application are stored on disk.
It is also important for your application to remain active with respect to the DCS 300.
When an application is inactive, the last transaction sent to the DCS 300 is stored in a
Hot Standby file along with any subsequent transactions. When the application
becomes active, the transactions are delivered, first in first out (FIFO), from the Hot
Standby file.
Summary of Contents for DCS 300
