Connecting to the Upline Network
3-19
3
Note:
The default configuration for the SDLC card is V.35. Contact your local
Intermec representative if you need to use RS-232 communications.
To install the DCS 300
1. Locate the slot that contains the SDLC card on the rear panel of your DCS 300. The
SDLC card is the card that is farthest right when you are facing the front panel. The
connector on the card looks like the figure below.
0300U024.eps
2. Insert one end of the cable in the port on the card and the other end in the
connection.
Configuring the SDLC Card
After you install the DCS 300, you need to turn it on and configure its network adapter
cards. The SDLC card can use an internal or external clock at speeds up to 1.5 Mbps.
Before you configure the network adapter card, obtain the local station address from
your network administrator. You may also need to know the line type, line mode, NRZI,
link station role, and maximum I-field size.
To configure the SDLC card
1. From the main screen, choose the type of host environment you are using to
communicate between the DCS 300 and the host.
2. Choose Local Network Adapter. Four buttons for different network adapter card
types appear.
3. Choose SDLC. The SDLC Adapter Configuration dialog box appears.
4. In the Local station field, enter the address (in hex) that identifies the DCS 300
station. The address can be from 01 to FE. The default is 01.
Summary of Contents for DCS 300
