background image

39 

Interphase Technologies, Inc. 

5 Year Limited Warranty 

 

Any unit that fails during the first year of the warranty period will, at 

Interphase’ option, be repaired or replaced at no charge to the customer 

provided it is returned to 

Interphase, freight prepaid with proof of date of 

purchase and a description of the malfunction.  Repair or replacement during the 

warranty period will not extend the basic warranty period. 

 

From the second through the fifth year, 

Interphase will, at its option, repair or 

replace defective units for a fixed fee.  This fee will be set at the beginning of 

each year.  More information about the fixed rate repair fee is available by 

calling Interphase at (831) 477-4944 or visit our website at:  

www.interphase-tech.com. 

 

This warranty does not apply to an 

Interphase product that has failed due to 

improper installation, misuse, or accident, nor does it apply to products which 

have been repaired or altered outside the 

Interphase factory. 

 

Transducers, GPS antennas and Radar Antennas are subject to extreme 

conditions beyond control of the manufacturer and 

Interphase.  Due to these 

conditions, the warranty on these components is limited to one year against 

defects in workmanship or materials.  The fixed fee for years two through five of 

the warranty does not apply to these components.  Any costs incurred with 

transducer or antenna replacement are specifically excluded from this warranty 

other than the cost of the components themselves. 

 

This warranty does not include incidental or consequential damages and 

Interphase disclaims any liability for any such damages.  All implied 

warranties, if any, are limited in duration to the above stated one year warranty 

period.  Some states and provinces do not allow the exclusion or limitation of 

incidental or consequential damages, therefore, the above limitations may not 

apply to you.   

 

The completion and return of the enclosed Warranty Registration Card is a 

condition precedent to the warranty coverage.  Owner must provide proof 

of date of purchase in order for warranty to be valid. 

 

This warranty gives you specific legal rights which may vary from state to state 

and province to province.  This warranty is limited only to the original purchaser 

of the unit. 

Summary of Contents for iScan V90









































Reviews: