background image

InTersPIrO’s lImITeD WarranTY

InTERSPIRO warrants this product against failure to comply with InTERSPIRO’s 

published specifications for the product and against defects in materials and 

workmanship for a period of twelve (12) months after date of purchase. Within 

that period, InTERSPIRO will, at its option, repair or replace the product or refund 

your purchase price if InTERSPIRO determines the product does not conform to 

InTERSPIRO´s specifications or is defective in material or workmanship.

To make a warranty claim, contact your authorized InTERSPIRO distributor or 

InTERSPIRO directly. For telephone inquiries please have your product invoice or 

other proof of purchase available. If you write, include proof of purchase and a 

written explanation of the problem. Warranty servicing will be provided on-site or 

at one of InTERSPIRO’s authorized service facilities, at InTERSPIRO’s discretion. If 

shipment to an authorized service facility is required, shipping instructions will be 

provided by InTERSPIRO or your authorized InTERSPIRO distributor. do not ship 

any product or component without shipping authorization. All shipping charges to 

InTERSPIRO’s service facility must be prepaid by the customer.

This limited warranty does not apply if the product has been (I) involved in an 

accident or subjected to misuse, improper maintenance or negligence; (II) altered 

or repaired in any way that has, in InTERSPIRO’s judgement, adversely affected 

its performance or reliability; (III) used in an application or for a purpose for which 

the product was not designed or under stresses or conditions exceeding those 

specified for the product; or (IV) damaged after leaving InTERSPIRO’s facility.

This limited warranty is valid only for the original purchaser, and is not 

transferable.

IMPORTAnT! This limited warranty is exclusive and is in lieu of all other 

warranties, expressed or implied, including any warranty of merchantability or 

fitness for a particular purpose. InTERSPIRO disclaims all other liabilities and 

obligations, including, to the extent allowed by law, non-contractual liability for 

personal injury or property damage based upon its negligence, strict liability or 

any other ground. To the full extent allowed by law, and regardless of whether 

liability is asserted on the basis of breach or warranty, negligence, strict liability, 

breach of contract or otherwise, InTERSPIRO shall not be responsible for special, 

incidental, consequential or punitive damages, including loss of property, loss of 

profits or revenues, down-time costs and the cost of substitute equipment (some 

states do not allow the exclusion or limitation of incidental or consequential 

damages, so the above limitation may not apply to you).

This warranty gives you specific legal rights, and you may also have other rights 

which vary from state to state.

Summary of Contents for 90USA























Reviews: